On Sat, 17 Sep 2022 17:51:28 -0700 (PDT), "russellseaton1@yahoo.com"
<ritzannaseaton@gmail.com> wrote:

>And it looks like I have enough room to cut the vertical 4" pipe (white) and put a correct drain flange on top of the subfloor in the bathroom. No separate flange and separate pipe sticking up through the floor. I'll glue in one of the normal flanges where the flange is screwed to the floor and the whole thing is glued to the pipe. As was done in the other bathroom but not this one for some reason.

Sound like a good plan.

On Saturday, September 17, 2022 at 9:01:50 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Saturday, September 17, 2022 at 7:51:30 PM UTC-5, russell...@yahoo.com wrote:
> > On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com wrote:
> > > On Thursday, September 15, 2022 at 1:13:09 AM UTC-5, DerbyDad03 wrote:
> > > > On Wednesday, September 14, 2022 at 8:11:27 PM UTC-4, russell...@yahoo.com wrote:
> > > > > I was able to get back over to the house and reassess things. Apparently having the subfloor exposed to the air resulted in a lot more damage over the past week. Amazing. I am positive the subfloor was not that damaged last time I looked at it. It will have to be replaced.
> > > > >
> > > > > I began the process. By drilling a couple holes in the floor near the drywall to mark out the back end of the patch. Looks like all the wood behind the toilet pipe in the joist bay will have to come out. Back to the drywall. And about 1 inch in front of the toilet pipe. That is the wood part. Easy enough to figure out. And I have to cut the new plywood subfloor around the toilet pipe and the water pipe sticking up through the floor. But that is just cutting and gluing and screwing pieces in place.
> > > > >
> > > > > Now the odd part. The toilet drain. Sticks up through the floor about 1/4" or so. But it has no flange on it. Where you put the T bolts that move back and forth and go up into the porcelain toilet. Its just a 4 inch pipe, plastic, with a rubber cone on top. About 1 inch or so thick rubber cone on top of the pipe. Tapered rubber cone. Obviously that is where the toilet sits down onto and the wax ring. But the flange for the T bolts is completely separate. I did not tear the toilet out so cannot remember if there was a separate ring that was also torn up. Assume so but I will have to ask. Buying a separate metal flange ring is no big deal. Easy to screw it down.
> > > > >
> > > > > But I am wondering about the support for the waste pipe in the basement. It has some metal straps underneath it to keep it in place. But its not really super solid. You can bang on the waste pipe and move it a little bit. I have never dealt with toilet drains that did not have the flange built into the pipe itself. Glued on fitting that has the screw holding slots. Fitting is glued onto the waste pipe. Then you screw the fitting into the subfloor. I can and likely will have to buy some more support straps and secure the waste pipe even more. And maybe add some wood blocking to really secure the waste pipe in place so it cannot possibly move.
> > > > >
> > > > > I'm sure it works. Having the flange that capture the T bolts completely separate from the waste pipe itself. But its different than what I am experienced with.
> > > > Have you measure the rough-in of the waste pipe? Any chance it
> > > > was this type of toilet?
> > > >
> > > > https://images.app.goo.gl/bPk7gh8sa4WDex3N9
> > > The old toilet is not like the ones shown in your link. I will have to look at the toilet again, its outside on the grass, to see if it looks normal. I assume it is a regular toilet. Waste out on the bottom that sits over a regular 4" drain pipe and flange with a wax ring. Normal. I will measure the pipe when I get back over there. Pretty sure its 4", but I will measure.
> > > >
> > > > Have you removed the rubber cone? Maybe the old plastic flange was
> > > > broken and removed. Then the cone was stuck in the pipe and a repair
> > > > ring was screwed to the floor as a separate piece.
> > > >
> > > > Any chance you could post a picture of what you currently have?
> > > I will try to take a picture of the waste pipe in the floor and figure out how to post it. Hopefully. I have not removed the rubber cone. That is generally not something you happily run your hands over. But I will probably have to monkey with it. The drain pipe is plastic. But no flange was attached and then cut off. No.
> > >
> > > The house is from the 1970s. It is one of those build in a factory houses. Where they build the two halves and truck them to the site and then lift them onto the basement foundation with a crane and then bolt the two halves together. And finish the very top of the roof ridge with shingles. So when it was built the bathrooms were finished except maybe the toilets and maybe sinks were not installed or hooked up. And then a plumber came in after the house was set on the foundation and did all the final water and drain pipe running in the basement. And maybe electrical connections too. The basement joists are covered on both sides with plywood. And the finish plumber cut out chunks of the plywood to run the pipes up to the bathrooms where they needed to be. The water pipes to the bathroom sinks and toilet are straight up through the floor. Not into the walls and then the pipe/valves out of the wall. A hole for the water pipe, and the toilet drain, straight up through the floor. So maybe it was easier and quicker to just drill a circle for the toilet drain pipe. Put the pipe up through the floor, put a rubber cone on it. Then screw a separate flange to the subfloor. Call it done. Put the toilet and wax ring on it. The bathroom sink did have the drain out of the wall. But it was a very big hole in the drywall. So I can imagine when the sink drain was hooked up, the plumber busted a huge hole in the drywall and used a long drill bit to drill down to the basement. Then the guy in the basement used a hole saw to make a big hole for the drain pipe that went up through the base plate of the wall and into the wall cavity.
> > Lets hope this works. Below are hopefully images from imgur.com. I am not sure which link is which picture. So I will add a description of each picture and count on you matching the description up to the right picture.
> >
> > https://i.imgur.com/cKOTQ0p.jpg
> > https://i.imgur.com/HJSU2Py.jpg
> > https://i.imgur.com/aVzjyzg.jpg
> > https://i.imgur.com/NobbGZc.jpg
> > https://i.imgur.com/vux8U3y.jpg
> > https://i.imgur.com/orbwV8N.jpg
> >
> > Pic 1: Toilet pipe sticking up through floor into bathroom. The rot of the wood does not show up as rotted as it really is. And the picture makes it seem like the hole for the pipe is a good fit. Its not. The rubber cap on top isn't really a cone. Its flat rubber on top of the white plastic pipe funnel.
> > Pic 2: Bigger picture of where the toilet will sit. Tape measure to give a sense of distance. Wood is rotted.
> > Pic 3: Whole bathroom. Or where the toilet will sit and where the new vanity will sit. Shows the waste pipe coming out of the wall and the water pipes coming up through the floor. Bathroom was repainted in the past.
> > Pic 4: Underside of the bathroom from the basement. Looking up into the floor joists. Wood around the pipe going through the floor is rotted all around.
> > Pic 5: Bigger picture from underneath and the basement. The other PVC black pipe going up is into the wall I think and catches the sink drains.
> > Pic 6: Even bigger picture. Showing the drain system under the joists in the basement. The second toilet drain in the other bathroom is at the end of the white plastic pipe. Its not shown in the picture.
> >
> > From the pictures it looks like I will replace all the subfloor above the drain pipe sticking up through the floor. Side to side in the joist bay and a couple inches in front of the toilet pipe. And back to the drywall. 12" x 18" total I think. And it looks like I have enough room to cut the vertical 4" pipe (white) and put a correct drain flange on top of the subfloor in the bathroom. No separate flange and separate pipe sticking up through the floor. I'll glue in one of the normal flanges where the flange is screwed to the floor and the whole thing is glued to the pipe. As was done in the other bathroom but not this one for some reason.
> Big thanks to DerbyDad03 for telling me about imgur.com and especially about the "Direct Link" choice. I never would have figured out that was the correct choice of all the options.

Here's another tip that I use with imgur all the time. It may sound complicated but
it's really easy.

First, I use Outlook as my PC mail client, so that's what I'll describe. You may have
to play with these steps to get it to work with whatever mail client you use.

Windows 10 comes with an app called Snipping Tool. I won't get into that, it's all
described here and many other places found with a simple web search.

https://www.youtube.com/watch?v=fWNA2js9JGc

OK, so let's say I want to copy something from a website, or a portion of picture,
or anything and post it as an image link, using imgur.

1 - Use the Snipping Tool to snip the part you want to use.
2 - In the Snipping Tool window that opens after you do the snip, choose:
File...Send to...Email Recipient (as attachment)
3 - Outlook will open a new email with the snip as a jpg attachment.
4 - Open imgur and go the page where you add your own images.
5 - Back in the email that the Snipping Tool created, grab the attachment
and drag it into the imgur window.

When you drop it, it will automatically be added to your images and you can
then create the "direct link".

On Saturday, September 17, 2022 at 11:04:12 PM UTC-5, DerbyDad03 wrote:
> On Saturday, September 17, 2022 at 9:01:50 PM UTC-4, russell...@yahoo.com wrote:
> > On Saturday, September 17, 2022 at 7:51:30 PM UTC-5, russell...@yahoo.com wrote:
> > > On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com wrote:
> > > > On Thursday, September 15, 2022 at 1:13:09 AM UTC-5, DerbyDad03 wrote:
> > > > > On Wednesday, September 14, 2022 at 8:11:27 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > I was able to get back over to the house and reassess things. Apparently having the subfloor exposed to the air resulted in a lot more damage over the past week. Amazing. I am positive the subfloor was not that damaged last time I looked at it. It will have to be replaced.
> > > > > >
> > > > > > I began the process. By drilling a couple holes in the floor near the drywall to mark out the back end of the patch. Looks like all the wood behind the toilet pipe in the joist bay will have to come out. Back to the drywall. And about 1 inch in front of the toilet pipe. That is the wood part. Easy enough to figure out. And I have to cut the new plywood subfloor around the toilet pipe and the water pipe sticking up through the floor. But that is just cutting and gluing and screwing pieces in place.
> > > > > >
> > > > > > Now the odd part. The toilet drain. Sticks up through the floor about 1/4" or so. But it has no flange on it. Where you put the T bolts that move back and forth and go up into the porcelain toilet. Its just a 4 inch pipe, plastic, with a rubber cone on top. About 1 inch or so thick rubber cone on top of the pipe. Tapered rubber cone. Obviously that is where the toilet sits down onto and the wax ring. But the flange for the T bolts is completely separate. I did not tear the toilet out so cannot remember if there was a separate ring that was also torn up. Assume so but I will have to ask. Buying a separate metal flange ring is no big deal. Easy to screw it down.
> > > > > >
> > > > > > But I am wondering about the support for the waste pipe in the basement. It has some metal straps underneath it to keep it in place. But its not really super solid. You can bang on the waste pipe and move it a little bit. I have never dealt with toilet drains that did not have the flange built into the pipe itself. Glued on fitting that has the screw holding slots. Fitting is glued onto the waste pipe. Then you screw the fitting into the subfloor. I can and likely will have to buy some more support straps and secure the waste pipe even more. And maybe add some wood blocking to really secure the waste pipe in place so it cannot possibly move.
> > > > > >
> > > > > > I'm sure it works. Having the flange that capture the T bolts completely separate from the waste pipe itself. But its different than what I am experienced with.
> > > > > Have you measure the rough-in of the waste pipe? Any chance it
> > > > > was this type of toilet?
> > > > >
> > > > > https://images.app.goo.gl/bPk7gh8sa4WDex3N9
> > > > The old toilet is not like the ones shown in your link. I will have to look at the toilet again, its outside on the grass, to see if it looks normal. I assume it is a regular toilet. Waste out on the bottom that sits over a regular 4" drain pipe and flange with a wax ring. Normal. I will measure the pipe when I get back over there. Pretty sure its 4", but I will measure.
> > > > >
> > > > > Have you removed the rubber cone? Maybe the old plastic flange was
> > > > > broken and removed. Then the cone was stuck in the pipe and a repair
> > > > > ring was screwed to the floor as a separate piece.
> > > > >
> > > > > Any chance you could post a picture of what you currently have?
> > > > I will try to take a picture of the waste pipe in the floor and figure out how to post it. Hopefully. I have not removed the rubber cone. That is generally not something you happily run your hands over. But I will probably have to monkey with it. The drain pipe is plastic. But no flange was attached and then cut off. No.
> > > >
> > > > The house is from the 1970s. It is one of those build in a factory houses. Where they build the two halves and truck them to the site and then lift them onto the basement foundation with a crane and then bolt the two halves together. And finish the very top of the roof ridge with shingles. So when it was built the bathrooms were finished except maybe the toilets and maybe sinks were not installed or hooked up. And then a plumber came in after the house was set on the foundation and did all the final water and drain pipe running in the basement. And maybe electrical connections too. The basement joists are covered on both sides with plywood. And the finish plumber cut out chunks of the plywood to run the pipes up to the bathrooms where they needed to be. The water pipes to the bathroom sinks and toilet are straight up through the floor. Not into the walls and then the pipe/valves out of the wall. A hole for the water pipe, and the toilet drain, straight up through the floor. So maybe it was easier and quicker to just drill a circle for the toilet drain pipe. Put the pipe up through the floor, put a rubber cone on it. Then screw a separate flange to the subfloor. Call it done.. Put the toilet and wax ring on it. The bathroom sink did have the drain out of the wall. But it was a very big hole in the drywall. So I can imagine when the sink drain was hooked up, the plumber busted a huge hole in the drywall and used a long drill bit to drill down to the basement. Then the guy in the basement used a hole saw to make a big hole for the drain pipe that went up through the base plate of the wall and into the wall cavity.
> > > Lets hope this works. Below are hopefully images from imgur.com. I am not sure which link is which picture. So I will add a description of each picture and count on you matching the description up to the right picture.
> > >
> > > https://i.imgur.com/cKOTQ0p.jpg
> > > https://i.imgur.com/HJSU2Py.jpg
> > > https://i.imgur.com/aVzjyzg.jpg
> > > https://i.imgur.com/NobbGZc.jpg
> > > https://i.imgur.com/vux8U3y.jpg
> > > https://i.imgur.com/orbwV8N.jpg
> > >
> > > Pic 1: Toilet pipe sticking up through floor into bathroom. The rot of the wood does not show up as rotted as it really is. And the picture makes it seem like the hole for the pipe is a good fit. Its not. The rubber cap on top isn't really a cone. Its flat rubber on top of the white plastic pipe funnel.
> > > Pic 2: Bigger picture of where the toilet will sit. Tape measure to give a sense of distance. Wood is rotted.
> > > Pic 3: Whole bathroom. Or where the toilet will sit and where the new vanity will sit. Shows the waste pipe coming out of the wall and the water pipes coming up through the floor. Bathroom was repainted in the past.
> > > Pic 4: Underside of the bathroom from the basement. Looking up into the floor joists. Wood around the pipe going through the floor is rotted all around.
> > > Pic 5: Bigger picture from underneath and the basement. The other PVC black pipe going up is into the wall I think and catches the sink drains.
> > > Pic 6: Even bigger picture. Showing the drain system under the joists in the basement. The second toilet drain in the other bathroom is at the end of the white plastic pipe. Its not shown in the picture.
> > >
> > > From the pictures it looks like I will replace all the subfloor above the drain pipe sticking up through the floor. Side to side in the joist bay and a couple inches in front of the toilet pipe. And back to the drywall. 12" x 18" total I think. And it looks like I have enough room to cut the vertical 4" pipe (white) and put a correct drain flange on top of the subfloor in the bathroom. No separate flange and separate pipe sticking up through the floor. I'll glue in one of the normal flanges where the flange is screwed to the floor and the whole thing is glued to the pipe. As was done in the other bathroom but not this one for some reason.
> > Big thanks to DerbyDad03 for telling me about imgur.com and especially about the "Direct Link" choice. I never would have figured out that was the correct choice of all the options.
> Here's another tip that I use with imgur all the time. It may sound complicated but
> it's really easy.
>
> First, I use Outlook as my PC mail client, so that's what I'll describe. You may have
> to play with these steps to get it to work with whatever mail client you use.
>
> Windows 10 comes with an app called Snipping Tool. I won't get into that, it's all
> described here and many other places found with a simple web search.
>
> https://www.youtube.com/watch?v=fWNA2js9JGc
>
> OK, so let's say I want to copy something from a website, or a portion of picture,
> or anything and post it as an image link, using imgur.
>
> 1 - Use the Snipping Tool to snip the part you want to use.
> 2 - In the Snipping Tool window that opens after you do the snip, choose:
> File...Send to...Email Recipient (as attachment)
> 3 - Outlook will open a new email with the snip as a jpg attachment.
> 4 - Open imgur and go the page where you add your own images.
> 5 - Back in the email that the Snipping Tool created, grab the attachment
> and drag it into the imgur window.
>
> When you drop it, it will automatically be added to your images and you can
> then create the "direct link".
>
> 6 - Close the email (the Snipping Tool is disabled until you close the email)
>
> Now, if you really want to get fancy, use PowerPoint, Paint, etc. to
> edit the snip before using the process above.
>
> To create the image at the link below
>
> 1 - I snipped a portion of one your images and pasted it into PowerPoint
> (the Snipping Tool puts its on your clipboard for you)
> 2 - I then added text and shapes to the image in PowerPoint.
> 3 - I then used the Snipping Tool on the *edited image* and followed the
> steps above to create the link.
>
> You'll note that at no point did I save the PowerPoint. I just used the app for
> editing and then "snipped the snip" and uploaded the new snip to imgur via the
> email drag and drop process.
>
> https://i.imgur.com/h81wgtA.jpg

On Saturday, September 17, 2022 at 8:55:43 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Saturday, September 17, 2022 at 7:51:30 PM UTC-5, russell...@yahoo.com wrote:
> > On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com wrote:
> > > On Thursday, September 15, 2022 at 1:13:09 AM UTC-5, DerbyDad03 wrote:
> > > > On Wednesday, September 14, 2022 at 8:11:27 PM UTC-4, russell...@yahoo.com wrote:
> > > > > I was able to get back over to the house and reassess things. Apparently having the subfloor exposed to the air resulted in a lot more damage over the past week. Amazing. I am positive the subfloor was not that damaged last time I looked at it. It will have to be replaced.
> > > > >
> > > > > I began the process. By drilling a couple holes in the floor near the drywall to mark out the back end of the patch. Looks like all the wood behind the toilet pipe in the joist bay will have to come out. Back to the drywall. And about 1 inch in front of the toilet pipe. That is the wood part. Easy enough to figure out. And I have to cut the new plywood subfloor around the toilet pipe and the water pipe sticking up through the floor. But that is just cutting and gluing and screwing pieces in place.
> > > > >
> > > > > Now the odd part. The toilet drain. Sticks up through the floor about 1/4" or so. But it has no flange on it. Where you put the T bolts that move back and forth and go up into the porcelain toilet. Its just a 4 inch pipe, plastic, with a rubber cone on top. About 1 inch or so thick rubber cone on top of the pipe. Tapered rubber cone. Obviously that is where the toilet sits down onto and the wax ring. But the flange for the T bolts is completely separate. I did not tear the toilet out so cannot remember if there was a separate ring that was also torn up. Assume so but I will have to ask. Buying a separate metal flange ring is no big deal. Easy to screw it down.
> > > > >
> > > > > But I am wondering about the support for the waste pipe in the basement. It has some metal straps underneath it to keep it in place. But its not really super solid. You can bang on the waste pipe and move it a little bit. I have never dealt with toilet drains that did not have the flange built into the pipe itself. Glued on fitting that has the screw holding slots. Fitting is glued onto the waste pipe. Then you screw the fitting into the subfloor. I can and likely will have to buy some more support straps and secure the waste pipe even more. And maybe add some wood blocking to really secure the waste pipe in place so it cannot possibly move.
> > > > >
> > > > > I'm sure it works. Having the flange that capture the T bolts completely separate from the waste pipe itself. But its different than what I am experienced with.
> > > > Have you measure the rough-in of the waste pipe? Any chance it
> > > > was this type of toilet?
> > > >
> > > > https://images.app.goo.gl/bPk7gh8sa4WDex3N9
> > > The old toilet is not like the ones shown in your link. I will have to look at the toilet again, its outside on the grass, to see if it looks normal. I assume it is a regular toilet. Waste out on the bottom that sits over a regular 4" drain pipe and flange with a wax ring. Normal. I will measure the pipe when I get back over there. Pretty sure its 4", but I will measure.
> > > >
> > > > Have you removed the rubber cone? Maybe the old plastic flange was
> > > > broken and removed. Then the cone was stuck in the pipe and a repair
> > > > ring was screwed to the floor as a separate piece.
> > > >
> > > > Any chance you could post a picture of what you currently have?
> > > I will try to take a picture of the waste pipe in the floor and figure out how to post it. Hopefully. I have not removed the rubber cone. That is generally not something you happily run your hands over. But I will probably have to monkey with it. The drain pipe is plastic. But no flange was attached and then cut off. No.
> > >
> > > The house is from the 1970s. It is one of those build in a factory houses. Where they build the two halves and truck them to the site and then lift them onto the basement foundation with a crane and then bolt the two halves together. And finish the very top of the roof ridge with shingles. So when it was built the bathrooms were finished except maybe the toilets and maybe sinks were not installed or hooked up. And then a plumber came in after the house was set on the foundation and did all the final water and drain pipe running in the basement. And maybe electrical connections too. The basement joists are covered on both sides with plywood. And the finish plumber cut out chunks of the plywood to run the pipes up to the bathrooms where they needed to be. The water pipes to the bathroom sinks and toilet are straight up through the floor. Not into the walls and then the pipe/valves out of the wall. A hole for the water pipe, and the toilet drain, straight up through the floor. So maybe it was easier and quicker to just drill a circle for the toilet drain pipe. Put the pipe up through the floor, put a rubber cone on it. Then screw a separate flange to the subfloor. Call it done. Put the toilet and wax ring on it. The bathroom sink did have the drain out of the wall. But it was a very big hole in the drywall. So I can imagine when the sink drain was hooked up, the plumber busted a huge hole in the drywall and used a long drill bit to drill down to the basement. Then the guy in the basement used a hole saw to make a big hole for the drain pipe that went up through the base plate of the wall and into the wall cavity.
> > Lets hope this works. Below are hopefully images from imgur.com. I am not sure which link is which picture. So I will add a description of each picture and count on you matching the description up to the right picture.
> >
> > https://i.imgur.com/cKOTQ0p.jpg
> > https://i.imgur.com/HJSU2Py.jpg
> > https://i.imgur.com/aVzjyzg.jpg
> > https://i.imgur.com/NobbGZc.jpg
> > https://i.imgur.com/vux8U3y.jpg
> > https://i.imgur.com/orbwV8N.jpg
> >
> > Pic 1: Toilet pipe sticking up through floor into bathroom. The rot of the wood does not show up as rotted as it really is. And the picture makes it seem like the hole for the pipe is a good fit. Its not. The rubber cap on top isn't really a cone. Its flat rubber on top of the white plastic pipe funnel.

When you said "rubber cone" I was thinking that it could be a Fernco Wax Free Toilet Seal.
It's obviously not that since we can see the top of the PVC pipe. It could still be a Fernco
of some type.

<https://www.fernco.com/videos/fernco-wax-free-toilet-seal-video>

If you are not familiar with Fernco couplings, you should look into them. They are great
for plumbing jobs where gluing might be difficult or things don't line up perfectly or you
might need to take them apart to clear hair, etc. on a regular basis. (like when there 3
women with long hair living under then same roof. Trust me on that one.)

Since there is no pressure in a drain pipe, they work great and AFAIK they are code
compliant in all residential drain systems.

<https://www.fernco.com/products/flexible-couplings/stock-couplings>

> > Pic 2: Bigger picture of where the toilet will sit. Tape measure to give a sense of distance. Wood is rotted.
> > Pic 3: Whole bathroom. Or where the toilet will sit and where the new vanity will sit. Shows the waste pipe coming out of the wall and the water pipes coming up through the floor. Bathroom was repainted in the past.
> > Pic 4: Underside of the bathroom from the basement. Looking up into the floor joists. Wood around the pipe going through the floor is rotted all around.
> > Pic 5: Bigger picture from underneath and the basement. The other PVC black pipe going up is into the wall I think and catches the sink drains.
> > Pic 6: Even bigger picture. Showing the drain system under the joists in the basement. The second toilet drain in the other bathroom is at the end of the white plastic pipe. Its not shown in the picture.
> >
> > From the pictures it looks like I will replace all the subfloor above the drain pipe sticking up through the floor. Side to side in the joist bay and a couple inches in front of the toilet pipe. And back to the drywall. 12" x 18" total I think. And it looks like I have enough room to cut the vertical 4" pipe (white) and put a correct drain flange on top of the subfloor in the bathroom. No separate flange and separate pipe sticking up through the floor. I'll glue in one of the normal flanges where the flange is screwed to the floor and the whole thing is glued to the pipe. As was done in the other bathroom but not this one for some reason.
> Forgot to add it, but in the second link, the 7" and 5" written on the floor in black marker is how far from the center of the drain pipe to the joists on each side. Pipe is not perfectly centered in the joist bay. And this joist bay is not exactly 16" on center either. More like 13.5" on center. Not that it makes any difference.

"russellseaton1@yahoo.com" <ritzannaseaton@gmail.com> writes:
>On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russellseaton1@yahoo.com=

>Lets hope this works. Below are hopefully images from imgur.com. I am not=
> sure which link is which picture. So I will add a description of each pic=
>ture and count on you matching the description up to the right picture.
>
>https://i.imgur.com/cKOTQ0p.jpg
>https://i.imgur.com/HJSU2Py.jpg
>https://i.imgur.com/aVzjyzg.jpg
>https://i.imgur.com/NobbGZc.jpg
>https://i.imgur.com/vux8U3y.jpg
>https://i.imgur.com/orbwV8N.jpg
>

I'd cut the waste pipe downstream of the elbow, replace
the section of floor, and reinstall a new integral closet flange[*],
a length of straight pipe, new elbow and a coupling to
the original waste pipe.

[*] Oatey 43587 or similar.

On Sunday, September 18, 2022 at 10:39:27 AM UTC-4, Scott Lurndal wrote:
> "russell...@yahoo.com" <ritzann...@gmail.com> writes:
> >On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com=
>
> >Lets hope this works. Below are hopefully images from imgur.com. I am not=
> > sure which link is which picture. So I will add a description of each pic=
> >ture and count on you matching the description up to the right picture.
> >
> >https://i.imgur.com/cKOTQ0p.jpg
> >https://i.imgur.com/HJSU2Py.jpg
> >https://i.imgur.com/aVzjyzg.jpg
> >https://i.imgur.com/NobbGZc.jpg
> >https://i.imgur.com/vux8U3y.jpg
> >https://i.imgur.com/orbwV8N.jpg
> >
> I'd cut the waste pipe downstream of the elbow, replace
> the section of floor, and reinstall a new integral closet flange[*],
> a length of straight pipe, new elbow and a coupling to
> the original waste pipe.
>
> [*] Oatey 43587 or similar.

What elbow? The one over by the wall? Why would you go back that far?

What about Sanitary Tee with the crappy caulk job? I'd cut the pipe on both
sides of the Sanitary Tee and replace that along with the pipe to the toilet.

That whole section could be connected to the existing drains pipes with 2
Fernco 1056-44 couplers.

https://i.imgur.com/88G8ve9.jpg

Am I missing something?

On Sunday, September 18, 2022 at 10:18:35 AM UTC-5, DerbyDad03 wrote:
> On Sunday, September 18, 2022 at 10:39:27 AM UTC-4, Scott Lurndal wrote:
> > "russell...@yahoo.com" <ritzann...@gmail.com> writes:
> > >On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com=
> >
> > >Lets hope this works. Below are hopefully images from imgur.com. I am not=
> > > sure which link is which picture. So I will add a description of each pic=
> > >ture and count on you matching the description up to the right picture..
> > >
> > >https://i.imgur.com/cKOTQ0p.jpg
> > >https://i.imgur.com/HJSU2Py.jpg
> > >https://i.imgur.com/aVzjyzg.jpg
> > >https://i.imgur.com/NobbGZc.jpg
> > >https://i.imgur.com/vux8U3y.jpg
> > >https://i.imgur.com/orbwV8N.jpg
> > >
> > I'd cut the waste pipe downstream of the elbow, replace
> > the section of floor, and reinstall a new integral closet flange[*],
> > a length of straight pipe, new elbow and a coupling to
> > the original waste pipe.
> >
> > [*] Oatey 43587 or similar.
> What elbow? The one over by the wall? Why would you go back that far?
>
> What about Sanitary Tee with the crappy caulk job? I'd cut the pipe on both
> sides of the Sanitary Tee and replace that along with the pipe to the toilet.
>
> That whole section could be connected to the existing drains pipes with 2
> Fernco 1056-44 couplers.
>
> https://i.imgur.com/88G8ve9.jpg
>
> Am I missing something?

I think Scott Lurndal and DerbyDad03 are both saying the same thing. Replace the 3 way connection on the main pipe, the pipe going up to the bathroom, and the new toilet flange on top in the bathroom. And put in new subfloor too. When I get back over there and look at everything I will figure out what to do.

I am aware of the comments about the 3 way connection not looking like its glued right. It does appear to have caulk put on the seam to stop leaking. I will look at that. I do not think there has been any leaking at that joint though. So.........no need to replace it if no leaks? Even though it looks bad? I will definitely look at it. And hopefully make the right choice.

I have access to everything in the basement. Its all below the joists. Just the toilet pipe going up is in the joists. Horizontal pipe is below the joists so easy to get to. At the end by the wall where the 90 degree is, I think there is a few inches of play so maybe when putting new parts in, I could use the glue in connectors. Not the rubber connectors from Fernco. See link below. I would need to move the pipe back a couple inches to get the new connectors into the line. To accommodate the overlap that is glued.

https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm

With the above coupling, I believe there are some that have a stop in the middle. And some that do not have a stop in the middle. So you could slide the whole thing over one side of the pipe, put glue on the area, and then slide the whole coupler back over. Not positive about this. Not sure how that would work or not. No offense against Fernco the rubber connector company. But it seems to me to glue the pipes all together is better.

On Sunday, September 18, 2022 at 11:56:35 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Sunday, September 18, 2022 at 10:18:35 AM UTC-5, DerbyDad03 wrote:
> > On Sunday, September 18, 2022 at 10:39:27 AM UTC-4, Scott Lurndal wrote:
> > > "russell...@yahoo.com" <ritzann...@gmail.com> writes:
> > > >On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com=
> > >
> > > >Lets hope this works. Below are hopefully images from imgur.com. I am not=
> > > > sure which link is which picture. So I will add a description of each pic=
> > > >ture and count on you matching the description up to the right picture.
> > > >
> > > >https://i.imgur.com/cKOTQ0p.jpg
> > > >https://i.imgur.com/HJSU2Py.jpg
> > > >https://i.imgur.com/aVzjyzg.jpg
> > > >https://i.imgur.com/NobbGZc.jpg
> > > >https://i.imgur.com/vux8U3y.jpg
> > > >https://i.imgur.com/orbwV8N.jpg
> > > >
> > > I'd cut the waste pipe downstream of the elbow, replace
> > > the section of floor, and reinstall a new integral closet flange[*],
> > > a length of straight pipe, new elbow and a coupling to
> > > the original waste pipe.
> > >
> > > [*] Oatey 43587 or similar.
> > What elbow? The one over by the wall? Why would you go back that far?
> >
> > What about Sanitary Tee with the crappy caulk job? I'd cut the pipe on both
> > sides of the Sanitary Tee and replace that along with the pipe to the toilet.
> >
> > That whole section could be connected to the existing drains pipes with 2
> > Fernco 1056-44 couplers.
> >
> > https://i.imgur.com/88G8ve9.jpg
> >
> > Am I missing something?
> I think Scott Lurndal and DerbyDad03 are both saying the same thing. Replace the 3 way connection on the main pipe, the pipe going up to the bathroom, and the new toilet flange on top in the bathroom. And put in new subfloor too. When I get back over there and look at everything I will figure out what to do.

We may *mean* the same thing, but we aren't *saying* the same thing. Since we
are trying to help you out in an area that you may not be knowledgeable, we should
use the correct terms to avoid confusion, especially since you need to buy parts.

The 3-way connection that you are referring is called a sanitary tee. If you went
to the store and asked for an elbow, you would not be shown a sanitary tee.

BTW a sanitary tee is different from a tee, in that the "tee" portion of a sanitary
tee is curved to facilitate the movement of waste material. It directs the waste
in a downstream direction, instead of dumping it straight down into the horizontal
pipe where it could cause an obstruction.

>
> I am aware of the comments about the 3 way connection not looking like its glued right. It does appear to have caulk put on the seam to stop leaking.. I will look at that. I do not think there has been any leaking at that joint though. So.........no need to replace it if no leaks? Even though it looks bad? I will definitely look at it. And hopefully make the right choice.

If it were me, I would replace it. The amount of extra work is minimal. (See below for an option)

>
> I have access to everything in the basement. Its all below the joists. Just the toilet pipe going up is in the joists. Horizontal pipe is below the joists so easy to get to. At the end by the wall where the 90 degree is, I think there is a few inches of play so maybe when putting new parts in, I could use the glue in connectors. Not the rubber connectors from Fernco. See link below. I would need to move the pipe back a couple inches to get the new connectors into the line. To accommodate the overlap that is glued.
>
> https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
>
> With the above coupling, I believe there are some that have a stop in the middle. And some that do not have a stop in the middle. So you could slide the whole thing over one side of the pipe, put glue on the area, and then slide the whole coupler back over. Not positive about this. Not sure how that would work or not. No offense against Fernco the rubber connector company. But it seems to me to glue the pipes all together is better.

You are referring to a stop coupling vs a no stop coupling. A no stop coupling is
often referred to as a repair coupling, although the term repair coupling is also
used for couplings that are adjustable in length. You don't need one of these. ;-)

<https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/b-k-reg-quick-fix-pvc-repair-coupling/160-503/p-1567664929834-c-8571.htm>

Personally, for your situation, I'd use Fernco couplings. Yes, a no stop coupling should
do the job, but it seems like a lot more work and mess. You've got to put glue on both
sections of pipe and then slide the coupling over the glue, pushing the glue out of the
way while making sure you get the fitting in place fast enough so the glue doesn't set. I
don't mean to sound like that tangled garden hose infomercial. ;-) Just seems to me
that the code compliant Fernco couplings are so much easier and essentially foolproof.

I've used no stop couplings when sweating copper because the solder is applied once the
fitting is in place, something you can't do with glue.

If you have room to move that pipe over by the wall enough to get stop couplings in place,
that might be the better option. Glue away. ;-)

Just FYI...Fernco also makes 4" sanitary tee's (QT-400, I believe) and Oatey makes a
compression fit flange that fits inside 4" PVC pipe. (43539). Toss in 2 of the 1546-44 4"
couplers and you could do the whole job without any glue. Cutting the pipe sections to
length would be only "hard" work. The rest is just tightening some screws. (and paying
for it)

Sanitary Tee
<https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI>

Flange
<https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>

Couplings
<https://www.amazon.com/Fernco-Flexible-Coupling-Plumbing-Connections/dp/B0B48DCPB7>

DerbyDad03 <teamarrows@eznet.net> writes:
>On Sunday, September 18, 2022 at 11:56:35 PM UTC-4, russellseaton1@yahoo.co=
>m wrote:
>> On Sunday, September 18, 2022 at 10:18:35 AM UTC-5, DerbyDad03 wrote:=20
>> > On Sunday, September 18, 2022 at 10:39:27 AM UTC-4, Scott Lurndal wrote=
>:=20
>> > > "russell...@yahoo.com" <ritzann...@gmail.com> writes:=20
>> > > >On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.=
>com=3D=20
>> > >=20
>> > > >Lets hope this works. Below are hopefully images from imgur.com. I a=
>m not=3D=20
>> > > > sure which link is which picture. So I will add a description of ea=
>ch pic=3D=20
>> > > >ture and count on you matching the description up to the right pictu=
>re.=20
>> > > >=20
>> > > >https://i.imgur.com/cKOTQ0p.jpg=20
>> > > >https://i.imgur.com/HJSU2Py.jpg=20
>> > > >https://i.imgur.com/aVzjyzg.jpg=20
>> > > >https://i.imgur.com/NobbGZc.jpg=20
>> > > >https://i.imgur.com/vux8U3y.jpg=20
>> > > >https://i.imgur.com/orbwV8N.jpg=20
>> > > >=20
>> > > I'd cut the waste pipe downstream of the elbow, replace=20
>> > > the section of floor, and reinstall a new integral closet flange[*],=
>=20
>> > > a length of straight pipe, new elbow and a coupling to=20
>> > > the original waste pipe.=20
>> > >=20
>> > > [*] Oatey 43587 or similar.=20
>> > What elbow? The one over by the wall? Why would you go back that far?=
>=20
>> >=20
>> > What about Sanitary Tee with the crappy caulk job? I'd cut the pipe on =
>both=20
>> > sides of the Sanitary Tee and replace that along with the pipe to the t=
>oilet.=20
>> >=20
>> > That whole section could be connected to the existing drains pipes with=
> 2=20
>> > Fernco 1056-44 couplers.=20
>> >=20
>> > https://i.imgur.com/88G8ve9.jpg=20
>> >=20
>> > Am I missing something?
>> I think Scott Lurndal and DerbyDad03 are both saying the same thing. Repl=
>ace the 3 way connection on the main pipe, the pipe going up to the bathroo=
>m, and the new toilet flange on top in the bathroom. And put in new subfloo=
>r too. When I get back over there and look at everything I will figure out =
>what to do.=20
>
>We may *mean* the same thing, but we aren't *saying* the same thing. a

That was my bad. The one photo that I looked at showed only part of the
'elbow' transitioning the vertical run from the closet into a horizontal run. It could
easily have been part of a tee rather than an LB. Replace it.

I was a bit surprised that the waste stack was PVC instead of ABS.

On Monday, September 19, 2022 at 1:03:24 PM UTC-5, Scott Lurndal wrote:
> DerbyDad03 <teama...@eznet.net> writes:
> >On Sunday, September 18, 2022 at 11:56:35 PM UTC-4, russell...@yahoo.co=
> >m wrote:
> >> On Sunday, September 18, 2022 at 10:18:35 AM UTC-5, DerbyDad03 wrote:=20
> >> > On Sunday, September 18, 2022 at 10:39:27 AM UTC-4, Scott Lurndal wrote=
> >:=20
> >> > > "russell...@yahoo.com" <ritzann...@gmail.com> writes:=20
> >> > > >On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.=
> >com=3D=20
> >> > >=20
> >> > > >Lets hope this works. Below are hopefully images from imgur.com. I a=
> >m not=3D=20
> >> > > > sure which link is which picture. So I will add a description of ea=
> >ch pic=3D=20
> >> > > >ture and count on you matching the description up to the right pictu=
> >re.=20
> >> > > >=20
> >> > > >https://i.imgur.com/cKOTQ0p.jpg=20
> >> > > >https://i.imgur.com/HJSU2Py.jpg=20
> >> > > >https://i.imgur.com/aVzjyzg.jpg=20
> >> > > >https://i.imgur.com/NobbGZc.jpg=20
> >> > > >https://i.imgur.com/vux8U3y.jpg=20
> >> > > >https://i.imgur.com/orbwV8N.jpg=20
> >> > > >=20
> >> > > I'd cut the waste pipe downstream of the elbow, replace=20
> >> > > the section of floor, and reinstall a new integral closet flange[*],=
> >=20
> >> > > a length of straight pipe, new elbow and a coupling to=20
> >> > > the original waste pipe.=20
> >> > >=20
> >> > > [*] Oatey 43587 or similar.=20
> >> > What elbow? The one over by the wall? Why would you go back that far?=
> >=20
> >> >=20
> >> > What about Sanitary Tee with the crappy caulk job? I'd cut the pipe on =
> >both=20
> >> > sides of the Sanitary Tee and replace that along with the pipe to the t=
> >oilet.=20
> >> >=20
> >> > That whole section could be connected to the existing drains pipes with=
> > 2=20
> >> > Fernco 1056-44 couplers.=20
> >> >=20
> >> > https://i.imgur.com/88G8ve9.jpg=20
> >> >=20
> >> > Am I missing something?
> >> I think Scott Lurndal and DerbyDad03 are both saying the same thing. Repl=
> >ace the 3 way connection on the main pipe, the pipe going up to the bathroo=
> >m, and the new toilet flange on top in the bathroom. And put in new subfloo=
> >r too. When I get back over there and look at everything I will figure out =
> >what to do.=20
> >
> >We may *mean* the same thing, but we aren't *saying* the same thing. a
>
> That was my bad. The one photo that I looked at showed only part of the
> 'elbow' transitioning the vertical run from the closet into a horizontal run. It could
> easily have been part of a tee rather than an LB. Replace it.
>
> I was a bit surprised that the waste stack was PVC instead of ABS.

The plumbing waste pipes have both PVC and ABS mixed together. One of the water drains, and maybe vents, is ABS. The two toilet waste pipes are PVC. And PVC for the long horizontal runs. I do not know plumbing code. But mixing them up does not seem to cause any harm. I will try to post one more picture showing all of the plumbing. The two toilet drains are PVC, and the one sink water drains is ABS. What I can see from the basement.

On Monday, September 19, 2022 at 12:34:10 PM UTC-5, DerbyDad03 wrote:
> On Sunday, September 18, 2022 at 11:56:35 PM UTC-4, russell...@yahoo.com wrote:
> > On Sunday, September 18, 2022 at 10:18:35 AM UTC-5, DerbyDad03 wrote:
> > > On Sunday, September 18, 2022 at 10:39:27 AM UTC-4, Scott Lurndal wrote:
> > > > "russell...@yahoo.com" <ritzann...@gmail.com> writes:
> > > > >On Friday, September 16, 2022 at 1:09:27 AM UTC-5, russell...@yahoo.com=
> > > >
> > > > >Lets hope this works. Below are hopefully images from imgur.com. I am not=
> > > > > sure which link is which picture. So I will add a description of each pic=
> > > > >ture and count on you matching the description up to the right picture.
> > > > >
> > > > >https://i.imgur.com/cKOTQ0p.jpg
> > > > >https://i.imgur.com/HJSU2Py.jpg
> > > > >https://i.imgur.com/aVzjyzg.jpg
> > > > >https://i.imgur.com/NobbGZc.jpg
> > > > >https://i.imgur.com/vux8U3y.jpg
> > > > >https://i.imgur.com/orbwV8N.jpg
> > > > >
> > > > I'd cut the waste pipe downstream of the elbow, replace
> > > > the section of floor, and reinstall a new integral closet flange[*],
> > > > a length of straight pipe, new elbow and a coupling to
> > > > the original waste pipe.
> > > >
> > > > [*] Oatey 43587 or similar.
> > > What elbow? The one over by the wall? Why would you go back that far?
> > >
> > > What about Sanitary Tee with the crappy caulk job? I'd cut the pipe on both
> > > sides of the Sanitary Tee and replace that along with the pipe to the toilet.
> > >
> > > That whole section could be connected to the existing drains pipes with 2
> > > Fernco 1056-44 couplers.
> > >
> > > https://i.imgur.com/88G8ve9.jpg
> > >
> > > Am I missing something?
> > I think Scott Lurndal and DerbyDad03 are both saying the same thing. Replace the 3 way connection on the main pipe, the pipe going up to the bathroom, and the new toilet flange on top in the bathroom. And put in new subfloor too. When I get back over there and look at everything I will figure out what to do.
> We may *mean* the same thing, but we aren't *saying* the same thing. Since we
> are trying to help you out in an area that you may not be knowledgeable, we should
> use the correct terms to avoid confusion, especially since you need to buy parts.
>
> The 3-way connection that you are referring is called a sanitary tee. If you went
> to the store and asked for an elbow, you would not be shown a sanitary tee.
>
> BTW a sanitary tee is different from a tee, in that the "tee" portion of a sanitary
> tee is curved to facilitate the movement of waste material. It directs the waste
> in a downstream direction, instead of dumping it straight down into the horizontal
> pipe where it could cause an obstruction.

OK. Maybe some words were mixed up somewhere. I'm not too concerned about that. I do know what parts are under question and need replacing. And I do know what they look like so when I go to Menards to get them, or go to Amazon, I can see if they are right or not. I know the 90 degree elbow at the end of the horizontal waste run is OK. No need to replace it. And the sanitary Tee does direct the water in the outgoing direction. Very important for a toilet. In another house I have a T that is just a regular T. Not directional. So when the washing machine water gets to that T, it kind of gets messed up. But there is no real problem with it. Its just not as right as it should be.

> >
> > I am aware of the comments about the 3 way connection not looking like its glued right. It does appear to have caulk put on the seam to stop leaking. I will look at that. I do not think there has been any leaking at that joint though. So.........no need to replace it if no leaks? Even though it looks bad? I will definitely look at it. And hopefully make the right choice.
> If it were me, I would replace it. The amount of extra work is minimal. (See below for an option)
> >
> > I have access to everything in the basement. Its all below the joists. Just the toilet pipe going up is in the joists. Horizontal pipe is below the joists so easy to get to. At the end by the wall where the 90 degree is, I think there is a few inches of play so maybe when putting new parts in, I could use the glue in connectors. Not the rubber connectors from Fernco. See link below. I would need to move the pipe back a couple inches to get the new connectors into the line. To accommodate the overlap that is glued.
> >
> > https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> >
> > With the above coupling, I believe there are some that have a stop in the middle. And some that do not have a stop in the middle. So you could slide the whole thing over one side of the pipe, put glue on the area, and then slide the whole coupler back over. Not positive about this. Not sure how that would work or not. No offense against Fernco the rubber connector company. But it seems to me to glue the pipes all together is better.
> You are referring to a stop coupling vs a no stop coupling. A no stop coupling is
> often referred to as a repair coupling, although the term repair coupling is also
> used for couplings that are adjustable in length. You don't need one of these. ;-)
>
> <https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/b-k-reg-quick-fix-pvc-repair-coupling/160-503/p-1567664929834-c-8571.htm>
>
> Personally, for your situation, I'd use Fernco couplings. Yes, a no stop coupling should
> do the job, but it seems like a lot more work and mess. You've got to put glue on both
> sections of pipe and then slide the coupling over the glue, pushing the glue out of the
> way while making sure you get the fitting in place fast enough so the glue doesn't set. I
> don't mean to sound like that tangled garden hose infomercial. ;-) Just seems to me
> that the code compliant Fernco couplings are so much easier and essentially foolproof.
>
> I've used no stop couplings when sweating copper because the solder is applied once the
> fitting is in place, something you can't do with glue.
>
> If you have room to move that pipe over by the wall enough to get stop couplings in place,
> that might be the better option. Glue away. ;-)

My comment about the no stop coupling was just in case somehow I did not have enough slack in the pipes to move them back and forth to get stop couplings in place. But I think I have enough slack to move things. So no need to use a no stop coupling. Yes I know doing a no stop coupling with PVC glue everywhere is not ideal at all. Kind of a last resort after you have jumped off the Grand Canyon rim and you might as well flap your arms on the way down.

>
> Just FYI...Fernco also makes 4" sanitary tee's (QT-400, I believe) and Oatey makes a
> compression fit flange that fits inside 4" PVC pipe. (43539). Toss in 2 of the 1546-44 4"
> couplers and you could do the whole job without any glue. Cutting the pipe sections to
> length would be only "hard" work. The rest is just tightening some screws.. (and paying
> for it)
>
> Sanitary Tee
> <https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI>
>
> Flange
> <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
>
> Couplings
> <https://www.amazon.com/Fernco-Flexible-Coupling-Plumbing-Connections/dp/B0B48DCPB7>

Man oh man. You are making this too easy. With the Fernco sanitary tee, I might be able to cut out the current sanitary tee with the caulk around the seams and put the Fernco tee in. Easy peasy. And for the toilet flange and drain, I would do the simple task of buying a PVC flange and gluing it to a short piece of 4" PVC pipe. Drop it down the hole I cut in the subfloor patch and then just shove it into the Fernco tee. All the plumbing work would be done in 15 minutes. That just does not seem right??????????

I am thinking if I go with a glue in sanitary tee, I will also have to use some short 4" PVC pipes and some of the glue in couplers. Stop couplers. And glue in the vertical toilet stack with the flange on it. So a lot more gluing and pieces involved. And cutting the pipe square to the right length. I have troubles cutting round pipes square if I cannot use my Ridgid tube cutter.

The Fernco sanitary tee says it is 5x10x13.3 inches. I wonder if that is the exact same size as regular PVC sanitary tee? Does the Fernco take into account the glue in flange part of the sanitary tee? Can you simply cut out the PVC bad sanitary tee and then the Fernco sanitary tee will fit perfectly into place and the extra rubber flanges will cover the existing 4" PVC drain pipe where you tighten the band clamps? Is it a perfect fit if you perfectly cut out the PVC tee?

On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russellseaton1@yahoo.com"
<ritzannaseaton@gmail.com> wrote:

>For PVC gluing, these are the parts I need.
>https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
>https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
>https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
>https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
>
>For the Fernco sanitary tee option.
>https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
>https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
>https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53

If you do glue, set it up dry, mark across the joints with a marker so
you can line them back up. Marking would the flange on the floor so
the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
usually.

I think I would go with Fernco route though, easier to line it up
nice. Quick and easy with existing plumbing is nice.

Nice thoughts DerbyDad.

On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> <ritzann...@gmail.com> wrote:
>
> >For PVC gluing, these are the parts I need.
> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> >
> >For the Fernco sanitary tee option.
> >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> If you do glue, set it up dry, mark across the joints with a marker so
> you can line them back up. Marking would the flange on the floor so
> the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> usually.
>
> I think I would go with Fernco route though, easier to line it up
> nice. Quick and easy with existing plumbing is nice.
>
> Nice thoughts DerbyDad.

Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.

For some reason, I don't like the Fernco option. It does not seem permanent. Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.

On Mon, 19 Sep 2022 20:56:59 -0700 (PDT), "russellseaton1@yahoo.com"
<ritzannaseaton@gmail.com> wrote:

>On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
>> On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
>> <ritzann...@gmail.com> wrote:
>>
>> >For PVC gluing, these are the parts I need.
>> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
>> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
>> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
>> >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
>> >
>> >For the Fernco sanitary tee option.
>> >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
>> >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
>> >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
>> If you do glue, set it up dry, mark across the joints with a marker so
>> you can line them back up. Marking would the flange on the floor so
>> the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
>> usually.
>>
>> I think I would go with Fernco route though, easier to line it up
>> nice. Quick and easy with existing plumbing is nice.
>>
>> Nice thoughts DerbyDad.
>
>Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
>
>For some reason, I don't like the Fernco option. It does not seem permanent. Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.

The thing with gluing a new sanitary tee is you will have get both
ends glued and put it together and in position, not easy if you are
experienced. The fernco stuff just use a bit of soapy water and it
slides easy and you have a bit of play in line it up.

But then I have a 3 inch copper pipe that drain cleaner ate a hole in
and it has been patched with Flex tape for a couple of years now. Got
repair pipe and a no stop connecter which does not go over the pipe,
just got 80 grit to fit the oscillating sander to widen it out, just
can not find that damn roundtuit.

On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > <ritzann...@gmail.com> wrote:
> >
> > >For PVC gluing, these are the parts I need.
> > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > >
> > >For the Fernco sanitary tee option.
> > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > If you do glue, set it up dry, mark across the joints with a marker so
> > you can line them back up. Marking would the flange on the floor so
> > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > usually.
> >
> > I think I would go with Fernco route though, easier to line it up
> > nice. Quick and easy with existing plumbing is nice.
> >
> > Nice thoughts DerbyDad.
> Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.

The thing to be aware of with dry fitting PVC is that fittings do not
typically seat fully when dry. You'll get close, but they'll slip in farther
once the glue is applied. Sometimes it's as much as a 50% difference
per joint.

Measuring the actual depth of the socket is actually the better option, especially
if you don't have any slack in the pipes.
Don't take my word for it...

<https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>

>
> For some reason, I don't like the Fernco option. It does not seem permanent.

Don't take this the wrong way, but when you use phrases like "for some reason"
and "it does not seem", it makes me think that you haven't done any research.

A simple Google search for fernco vs. glue (or however you like to phrase your
search strings) may convince you that Fernco (or Fernco like fittings) are not
just for temporary connections. Look at some of the plumbing forums. Pros
use them all the time.

> Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.

First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
where you trust Fernco couplings, just use a straight coupler to extend the pipes
on both sides of the S-Tee

Maybe I'm missing something, but it sounds like you are almost willing to use a
a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
in that thinking.

re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."

I didn't see any mention of the Oatey compression fit flange that I linked to:

<https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>

By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
If you don't already have glue available, you'd be buying glue and cleaner/primer for
one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
plan on looking into it a little further for my own edification) They make one style for
PVC pipes and one for cast iron.

On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > <ritzann...@gmail.com> wrote:
> > >
> > > >For PVC gluing, these are the parts I need.
> > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > >
> > > >For the Fernco sanitary tee option.
> > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > If you do glue, set it up dry, mark across the joints with a marker so
> > > you can line them back up. Marking would the flange on the floor so
> > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > usually.
> > >
> > > I think I would go with Fernco route though, easier to line it up
> > > nice. Quick and easy with existing plumbing is nice.
> > >
> > > Nice thoughts DerbyDad.
> > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> The thing to be aware of with dry fitting PVC is that fittings do not
> typically seat fully when dry. You'll get close, but they'll slip in farther
> once the glue is applied. Sometimes it's as much as a 50% difference
> per joint.
>
> Measuring the actual depth of the socket is actually the better option, especially
> if you don't have any slack in the pipes.
>
> Don't take my word for it...
>
> <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> >
> > For some reason, I don't like the Fernco option. It does not seem permanent.
> Don't take this the wrong way, but when you use phrases like "for some reason"
> and "it does not seem", it makes me think that you haven't done any research.
>
> A simple Google search for fernco vs. glue (or however you like to phrase your
> search strings) may convince you that Fernco (or Fernco like fittings) are not
> just for temporary connections. Look at some of the plumbing forums. Pros
> use them all the time.
> > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> where you trust Fernco couplings, just use a straight coupler to extend the pipes
> on both sides of the S-Tee
>
> Maybe I'm missing something, but it sounds like you are almost willing to use a
> a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> in that thinking.
>
> re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
>
> I didn't see any mention of the Oatey compression fit flange that I linked to:
>
> <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
>
> By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> If you don't already have glue available, you'd be buying glue and cleaner/primer for
> one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> plan on looking into it a little further for my own edification) They make one style for
> PVC pipes and one for cast iron.

Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!

As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.

I think the Fernco sanitary tee fits in without lengthening the pipe itself.. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.

I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.

On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > <ritzann...@gmail.com> wrote:
> > > >
> > > > >For PVC gluing, these are the parts I need.
> > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > >
> > > > >For the Fernco sanitary tee option.
> > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > you can line them back up. Marking would the flange on the floor so
> > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > usually.
> > > >
> > > > I think I would go with Fernco route though, easier to line it up
> > > > nice. Quick and easy with existing plumbing is nice.
> > > >
> > > > Nice thoughts DerbyDad.
> > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > The thing to be aware of with dry fitting PVC is that fittings do not
> > typically seat fully when dry. You'll get close, but they'll slip in farther
> > once the glue is applied. Sometimes it's as much as a 50% difference
> > per joint.
> >
> > Measuring the actual depth of the socket is actually the better option, especially
> > if you don't have any slack in the pipes.
> >
> > Don't take my word for it...
> >
> > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > >
> > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > Don't take this the wrong way, but when you use phrases like "for some reason"
> > and "it does not seem", it makes me think that you haven't done any research.
> >
> > A simple Google search for fernco vs. glue (or however you like to phrase your
> > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > just for temporary connections. Look at some of the plumbing forums. Pros
> > use them all the time.
> > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > on both sides of the S-Tee
> >
> > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > in that thinking.
> >
> > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> >
> > I didn't see any mention of the Oatey compression fit flange that I linked to:
> >
> > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> >
> > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > plan on looking into it a little further for my own edification) They make one style for
> > PVC pipes and one for cast iron.
> Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
>
> As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
>
> I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
>
> I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement.. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.

Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)

I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
and it would be connected to the existing drain.

Like this, but with a new S-Tee and vertical pipe.

https://i.imgur.com/88G8ve9.jpg

On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell...@yahoo.com wrote:
> > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > > <ritzann...@gmail.com> wrote:
> > > > >
> > > > > >For PVC gluing, these are the parts I need.
> > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > >
> > > > > >For the Fernco sanitary tee option.
> > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > you can line them back up. Marking would the flange on the floor so
> > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > usually.
> > > > >
> > > > > I think I would go with Fernco route though, easier to line it up
> > > > > nice. Quick and easy with existing plumbing is nice.
> > > > >
> > > > > Nice thoughts DerbyDad.
> > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > per joint.
> > >
> > > Measuring the actual depth of the socket is actually the better option, especially
> > > if you don't have any slack in the pipes.
> > >
> > > Don't take my word for it...
> > >
> > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > >
> > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > and "it does not seem", it makes me think that you haven't done any research.
> > >
> > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > use them all the time.
> > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > on both sides of the S-Tee
> > >
> > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > in that thinking.
> > >
> > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > >
> > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > >
> > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > >
> > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > plan on looking into it a little further for my own edification) They make one style for
> > > PVC pipes and one for cast iron.
> > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> >
> > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> >
> > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> >
> > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
>
> I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> and it would be connected to the existing drain.
>
> Like this, but with a new S-Tee and vertical pipe.
>
> https://i.imgur.com/88G8ve9.jpg

On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russellseaton1@yahoo.com wrote:
> On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell...@yahoo.com wrote:
> > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > > > <ritzann...@gmail.com> wrote:
> > > > > >
> > > > > > >For PVC gluing, these are the parts I need.
> > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > >
> > > > > > >For the Fernco sanitary tee option.
> > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > usually.
> > > > > >
> > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > nice. Quick and easy with existing plumbing is nice.
> > > > > >
> > > > > > Nice thoughts DerbyDad.
> > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > per joint.
> > > >
> > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > if you don't have any slack in the pipes.
> > > >
> > > > Don't take my word for it...
> > > >
> > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > >
> > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > and "it does not seem", it makes me think that you haven't done any research.
> > > >
> > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > just for temporary connections. Look at some of the plumbing forums.. Pros
> > > > use them all the time.
> > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > on both sides of the S-Tee
> > > >
> > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > > in that thinking.
> > > >
> > > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > > >
> > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > >
> > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > >
> > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > plan on looking into it a little further for my own edification) They make one style for
> > > > PVC pipes and one for cast iron.
> > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > >
> > > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> > >
> > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> > >
> > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
> >
> > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> > and it would be connected to the existing drain.
> >
> > Like this, but with a new S-Tee and vertical pipe.
> >
> > https://i.imgur.com/88G8ve9.jpg
> OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
>
> BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
>
> Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
>
> https://i.imgur.com/MqSNl53.jpg
> https://i.imgur.com/sXIC15n.jpg
> https://i.imgur.com/LvB4dxX.jpg
>
> Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
>
> Here are links for the fixed subfloor and the new toilet flange.
>
> https://i.imgur.com/8FbjkBh.jpg
> https://i.imgur.com/sl4Pxqo.jpg
>
> First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
>
> Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
>
> For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
>
> One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
>
> https://i.imgur.com/jHVgO4T.jpg
>
> DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.

On Monday, September 26, 2022 at 5:04:29 PM UTC-5, DerbyDad03 wrote:
> On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russell...@yahoo.com wrote:
> > On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell...@yahoo.com wrote:
> > > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > > > > <ritzann...@gmail.com> wrote:
> > > > > > >
> > > > > > > >For PVC gluing, these are the parts I need.
> > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571..htm?tid=-1130025097665889175&ipos=48
> > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > >
> > > > > > > >For the Fernco sanitary tee option.
> > > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > > usually.
> > > > > > >
> > > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > > nice. Quick and easy with existing plumbing is nice.
> > > > > > >
> > > > > > > Nice thoughts DerbyDad.
> > > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > > per joint.
> > > > >
> > > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > > if you don't have any slack in the pipes.
> > > > >
> > > > > Don't take my word for it...
> > > > >
> > > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > > >
> > > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > > and "it does not seem", it makes me think that you haven't done any research.
> > > > >
> > > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > > > use them all the time.
> > > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it.. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > > on both sides of the S-Tee
> > > > >
> > > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue.. I don't see the logic
> > > > > in that thinking.
> > > > >
> > > > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > > > >
> > > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > > >
> > > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > > >
> > > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > > plan on looking into it a little further for my own edification) They make one style for
> > > > > PVC pipes and one for cast iron.
> > > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > > >
> > > > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> > > >
> > > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> > > >
> > > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> > > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > > fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
> > >
> > > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > > PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> > > and it would be connected to the existing drain.
> > >
> > > Like this, but with a new S-Tee and vertical pipe.
> > >
> > > https://i.imgur.com/88G8ve9.jpg
> > OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
> >
> > BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
> >
> > Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
> >
> > https://i.imgur.com/MqSNl53.jpg
> > https://i.imgur.com/sXIC15n.jpg
> > https://i.imgur.com/LvB4dxX.jpg
> >
> > Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
> >
> > Here are links for the fixed subfloor and the new toilet flange.
> >
> > https://i.imgur.com/8FbjkBh.jpg
> > https://i.imgur.com/sl4Pxqo.jpg
> >
> > First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
> >
> > Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
> >
> > For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
> >
> > One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
> >
> > https://i.imgur.com/jHVgO4T.jpg
> >
> > DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.
> Good job! Looks great. Plumbing can be a pain, but for the most part
> it’s not all that hard - when you can get to what you need to get to.
>
> I’ve done similar jobs, but had to go in through a hole in the ceiling
> below. That’s the worst for me because I wasn’t born with the drywall
> mudding gene. It takes me forever and I’m rarely satisfied with the
> results.
>
> Good luck with the floor and fixtures. Paint first. ;-)

On Tuesday, September 27, 2022 at 2:20:22 AM UTC-4, russellseaton1@yahoo.com wrote:
> On Monday, September 26, 2022 at 5:04:29 PM UTC-5, DerbyDad03 wrote:
> > On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russell...@yahoo.com wrote:
> > > On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > > > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell...@yahoo.com wrote:
> > > > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo..com"
> > > > > > > > <ritzann...@gmail.com> wrote:
> > > > > > > >
> > > > > > > > >For PVC gluing, these are the parts I need.
> > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > >
> > > > > > > > >For the Fernco sanitary tee option.
> > > > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > > > usually.
> > > > > > > >
> > > > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > > > nice. Quick and easy with existing plumbing is nice.
> > > > > > > >
> > > > > > > > Nice thoughts DerbyDad.
> > > > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > > > per joint.
> > > > > >
> > > > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > > > if you don't have any slack in the pipes.
> > > > > >
> > > > > > Don't take my word for it...
> > > > > >
> > > > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > > > >
> > > > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > > > and "it does not seem", it makes me think that you haven't done any research.
> > > > > >
> > > > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > > > > use them all the time.
> > > > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > > > on both sides of the S-Tee
> > > > > >
> > > > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > > > > in that thinking.
> > > > > >
> > > > > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > > > > >
> > > > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > > > >
> > > > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > > > >
> > > > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > > > plan on looking into it a little further for my own edification) They make one style for
> > > > > > PVC pipes and one for cast iron.
> > > > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > > > >
> > > > > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> > > > >
> > > > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight.. It has an advantage.
> > > > >
> > > > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> > > > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > > > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > > > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > > > fits perfectly. I'll be surprised if it does...just sounds too easy.. ;-)
> > > >
> > > > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > > > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > > > PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> > > > and it would be connected to the existing drain.
> > > >
> > > > Like this, but with a new S-Tee and vertical pipe.
> > > >
> > > > https://i.imgur.com/88G8ve9.jpg
> > > OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
> > >
> > > BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
> > >
> > > Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
> > >
> > > https://i.imgur.com/MqSNl53.jpg
> > > https://i.imgur.com/sXIC15n.jpg
> > > https://i.imgur.com/LvB4dxX.jpg
> > >
> > > Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
> > >
> > > Here are links for the fixed subfloor and the new toilet flange.
> > >
> > > https://i.imgur.com/8FbjkBh.jpg
> > > https://i.imgur.com/sl4Pxqo.jpg
> > >
> > > First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
> > >
> > > Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
> > >
> > > For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
> > >
> > > One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
> > >
> > > https://i.imgur.com/jHVgO4T.jpg
> > >
> > > DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.
> > Good job! Looks great. Plumbing can be a pain, but for the most part
> > it’s not all that hard - when you can get to what you need to get to.
> >
> > I’ve done similar jobs, but had to go in through a hole in the ceiling
> > below. That’s the worst for me because I wasn’t born with the drywall
> > mudding gene. It takes me forever and I’m rarely satisfied with the
> > results.
> >
> > Good luck with the floor and fixtures. Paint first. ;-)
> I love love love electrical work. Tolerate but do not like plumbing work. As for going through a hole, I recently added some lights into the garage. Accessed by an access panel and 8 foot step ladder. Crawled around on my hands and knees and belly on pieces of wood and plywood I brought up to span the trusses. Took several days and many hours. But I still liked that better than this plumbing work. I don't mind painting. Maybe because a freshly painted room always looks nice. Confirmation that you did something good.
>
> I'm reasonably happy with the finished job. Its right. But knowing what I know now, after doing it my way, I would do it your way the next time. As you described above of putting PVC sanitary T and stack and flange. Then use the rubber Fernco couplers to tie it into the horizontal run. Not that there will be a next time. Next time may be the other bathroom in the house. The one with the toilet still working. I probably cannot do a plumbing fix in there until we are ready to put in the vinyl flooring. Maybe do the plumbing fix the night before and the day the flooring installer is there. Vinyl flooring install will be hired out.
>
> Yes, painting is next job to be done. Before flooring is installed. And install new ceiling fans. One worry I have is getting the new cabinets in. The water supply lines come up through the floor. So have to take the valves off, figure out where to drill holes in the floor of the cabinet, then drop it over the water pipes. All while maneuvering the cabinet over the drain pipes coming out of the wall. I think bathroom vanities come with an open back or a big opening in the back. So no cutting a hole by me. But I will look at bathroom vanities next time I am at the store.

On Tuesday, September 27, 2022 at 4:51:37 PM UTC-5, DerbyDad03 wrote:
> On Tuesday, September 27, 2022 at 2:20:22 AM UTC-4, russell...@yahoo.com wrote:
> > On Monday, September 26, 2022 at 5:04:29 PM UTC-5, DerbyDad03 wrote:
> > > On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russell...@yahoo.com wrote:
> > > > On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > > > > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell....@yahoo.com wrote:
> > > > > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > > > > > > <ritzann...@gmail.com> wrote:
> > > > > > > > >
> > > > > > > > > >For PVC gluing, these are the parts I need.
> > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > >
> > > > > > > > > >For the Fernco sanitary tee option.
> > > > > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > > > > usually.
> > > > > > > > >
> > > > > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > > > > nice. Quick and easy with existing plumbing is nice.
> > > > > > > > >
> > > > > > > > > Nice thoughts DerbyDad.
> > > > > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > > > > per joint.
> > > > > > >
> > > > > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > > > > if you don't have any slack in the pipes.
> > > > > > >
> > > > > > > Don't take my word for it...
> > > > > > >
> > > > > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > > > > >
> > > > > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > > > > and "it does not seem", it makes me think that you haven't done any research.
> > > > > > >
> > > > > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > > > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > > > > > use them all the time.
> > > > > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > > > > on both sides of the S-Tee
> > > > > > >
> > > > > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > > > > > in that thinking.
> > > > > > >
> > > > > > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > > > > > >
> > > > > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > > > > >
> > > > > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > > > > >
> > > > > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > > > > plan on looking into it a little further for my own edification) They make one style for
> > > > > > > PVC pipes and one for cast iron.
> > > > > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > > > > >
> > > > > > As for my wanting, wishing I could do it with glued PVC instead.. Probably because houses are always built new and renovated with glued PVC.. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> > > > > >
> > > > > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> > > > > >
> > > > > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> > > > > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > > > > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > > > > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > > > > fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
> > > > >
> > > > > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > > > > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > > > > PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> > > > > and it would be connected to the existing drain.
> > > > >
> > > > > Like this, but with a new S-Tee and vertical pipe.
> > > > >
> > > > > https://i.imgur.com/88G8ve9.jpg
> > > > OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
> > > >
> > > > BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
> > > >
> > > > Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
> > > >
> > > > https://i.imgur.com/MqSNl53.jpg
> > > > https://i.imgur.com/sXIC15n.jpg
> > > > https://i.imgur.com/LvB4dxX.jpg
> > > >
> > > > Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
> > > >
> > > > Here are links for the fixed subfloor and the new toilet flange.
> > > >
> > > > https://i.imgur.com/8FbjkBh.jpg
> > > > https://i.imgur.com/sl4Pxqo.jpg
> > > >
> > > > First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
> > > >
> > > > Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything.. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
> > > >
> > > > For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
> > > >
> > > > One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
> > > >
> > > > https://i.imgur.com/jHVgO4T.jpg
> > > >
> > > > DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.
> > > Good job! Looks great. Plumbing can be a pain, but for the most part
> > > it’s not all that hard - when you can get to what you need to get to.
> > >
> > > I’ve done similar jobs, but had to go in through a hole in the ceiling
> > > below. That’s the worst for me because I wasn’t born with the drywall
> > > mudding gene. It takes me forever and I’m rarely satisfied with the
> > > results.
> > >
> > > Good luck with the floor and fixtures. Paint first. ;-)
> > I love love love electrical work. Tolerate but do not like plumbing work. As for going through a hole, I recently added some lights into the garage. Accessed by an access panel and 8 foot step ladder. Crawled around on my hands and knees and belly on pieces of wood and plywood I brought up to span the trusses. Took several days and many hours. But I still liked that better than this plumbing work. I don't mind painting. Maybe because a freshly painted room always looks nice. Confirmation that you did something good.
> >
> > I'm reasonably happy with the finished job. Its right. But knowing what I know now, after doing it my way, I would do it your way the next time. As you described above of putting PVC sanitary T and stack and flange. Then use the rubber Fernco couplers to tie it into the horizontal run. Not that there will be a next time. Next time may be the other bathroom in the house.. The one with the toilet still working. I probably cannot do a plumbing fix in there until we are ready to put in the vinyl flooring. Maybe do the plumbing fix the night before and the day the flooring installer is there. Vinyl flooring install will be hired out.
> >
> > Yes, painting is next job to be done. Before flooring is installed. And install new ceiling fans. One worry I have is getting the new cabinets in. The water supply lines come up through the floor. So have to take the valves off, figure out where to drill holes in the floor of the cabinet, then drop it over the water pipes. All while maneuvering the cabinet over the drain pipes coming out of the wall. I think bathroom vanities come with an open back or a big opening in the back. So no cutting a hole by me. But I will look at bathroom vanities next time I am at the store.
> Just because the pipes come up through the floor now doesn't mean that they have to
> stay there.
>
> Get some SharkBite fittings and few short lengths of PEX. Cut the copper pipes down in
> the basement and route the PEX inside the wall where the sink drain is. Bring the PEX
> into the back of the vanity, leaving a nice open bottom for "stuff". Pipes in the middle
> of a vanity bottom are just a PITA. Make your life even easier and cut out some of the
> drywall for better access. Hide it with the vanity.
>
> An example configuration...
>
> https://i.imgur.com/ym4ijXE.jpg
>
> If you hate plumbing, and you've never used SharkBites, ignore the cost and get it done in
> a matter of minutes. Easy transition from copper to PEX. No solder, no glue, minimal layout.
> Just push to fit. You don't even have to really line anything up, because once installed, they
> rotate on the pipe, so just point them in the direction you need. They are easier than Fernco
> couplings and just as permanent. ;-)
>
> https://www.sharkbite.com/us/en/brass-push-to-connect/fittings

On Tuesday, September 27, 2022 at 11:16:33 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Tuesday, September 27, 2022 at 4:51:37 PM UTC-5, DerbyDad03 wrote:
> > On Tuesday, September 27, 2022 at 2:20:22 AM UTC-4, russell...@yahoo.com wrote:
> > > On Monday, September 26, 2022 at 5:04:29 PM UTC-5, DerbyDad03 wrote:
> > > > On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russell...@yahoo..com wrote:
> > > > > On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > > > > > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > > > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell....@yahoo.com wrote:
> > > > > > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > > > > > > > <ritzann...@gmail.com> wrote:
> > > > > > > > > >
> > > > > > > > > > >For PVC gluing, these are the parts I need.
> > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > > >
> > > > > > > > > > >For the Fernco sanitary tee option.
> > > > > > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > > > > > usually.
> > > > > > > > > >
> > > > > > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > > > > > nice. Quick and easy with existing plumbing is nice.
> > > > > > > > > >
> > > > > > > > > > Nice thoughts DerbyDad.
> > > > > > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > > > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > > > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > > > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > > > > > per joint.
> > > > > > > >
> > > > > > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > > > > > if you don't have any slack in the pipes.
> > > > > > > >
> > > > > > > > Don't take my word for it...
> > > > > > > >
> > > > > > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > > > > > >
> > > > > > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > > > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > > > > > and "it does not seem", it makes me think that you haven't done any research.
> > > > > > > >
> > > > > > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > > > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > > > > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > > > > > > use them all the time.
> > > > > > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > > > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > > > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > > > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > > > > > on both sides of the S-Tee
> > > > > > > >
> > > > > > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > > > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > > > > > > in that thinking.
> > > > > > > >
> > > > > > > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > > > > > > >
> > > > > > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > > > > > >
> > > > > > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > > > > > >
> > > > > > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > > > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > > > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > > > > > plan on looking into it a little further for my own edification) They make one style for
> > > > > > > > PVC pipes and one for cast iron.
> > > > > > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > > > > > >
> > > > > > > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper..) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes.. They do not have only Fernco products for all their plumbing.
> > > > > > >
> > > > > > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> > > > > > >
> > > > > > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> > > > > > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > > > > > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > > > > > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > > > > > fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
> > > > > >
> > > > > > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > > > > > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > > > > > PVC S-Tee and glue it to the bottom of the pipe from the toilet.. Two Fernco couplings later
> > > > > > and it would be connected to the existing drain.
> > > > > >
> > > > > > Like this, but with a new S-Tee and vertical pipe.
> > > > > >
> > > > > > https://i.imgur.com/88G8ve9.jpg
> > > > > OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
> > > > >
> > > > > BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
> > > > >
> > > > > Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
> > > > >
> > > > > https://i.imgur.com/MqSNl53.jpg
> > > > > https://i.imgur.com/sXIC15n.jpg
> > > > > https://i.imgur.com/LvB4dxX.jpg
> > > > >
> > > > > Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
> > > > >
> > > > > Here are links for the fixed subfloor and the new toilet flange.
> > > > >
> > > > > https://i.imgur.com/8FbjkBh.jpg
> > > > > https://i.imgur.com/sl4Pxqo.jpg
> > > > >
> > > > > First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
> > > > >
> > > > > Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
> > > > >
> > > > > For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
> > > > >
> > > > > One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
> > > > >
> > > > > https://i.imgur.com/jHVgO4T.jpg
> > > > >
> > > > > DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.
> > > > Good job! Looks great. Plumbing can be a pain, but for the most part
> > > > it’s not all that hard - when you can get to what you need to get to.
> > > >
> > > > I’ve done similar jobs, but had to go in through a hole in the ceiling
> > > > below. That’s the worst for me because I wasn’t born with the drywall
> > > > mudding gene. It takes me forever and I’m rarely satisfied with the
> > > > results.
> > > >
> > > > Good luck with the floor and fixtures. Paint first. ;-)
> > > I love love love electrical work. Tolerate but do not like plumbing work. As for going through a hole, I recently added some lights into the garage. Accessed by an access panel and 8 foot step ladder. Crawled around on my hands and knees and belly on pieces of wood and plywood I brought up to span the trusses. Took several days and many hours. But I still liked that better than this plumbing work. I don't mind painting. Maybe because a freshly painted room always looks nice. Confirmation that you did something good.
> > >
> > > I'm reasonably happy with the finished job. Its right. But knowing what I know now, after doing it my way, I would do it your way the next time. As you described above of putting PVC sanitary T and stack and flange. Then use the rubber Fernco couplers to tie it into the horizontal run. Not that there will be a next time. Next time may be the other bathroom in the house. The one with the toilet still working. I probably cannot do a plumbing fix in there until we are ready to put in the vinyl flooring. Maybe do the plumbing fix the night before and the day the flooring installer is there. Vinyl flooring install will be hired out.
> > >
> > > Yes, painting is next job to be done. Before flooring is installed. And install new ceiling fans. One worry I have is getting the new cabinets in. The water supply lines come up through the floor. So have to take the valves off, figure out where to drill holes in the floor of the cabinet, then drop it over the water pipes. All while maneuvering the cabinet over the drain pipes coming out of the wall. I think bathroom vanities come with an open back or a big opening in the back. So no cutting a hole by me. But I will look at bathroom vanities next time I am at the store.
> > Just because the pipes come up through the floor now doesn't mean that they have to
> > stay there.
> >
> > Get some SharkBite fittings and few short lengths of PEX. Cut the copper pipes down in
> > the basement and route the PEX inside the wall where the sink drain is. Bring the PEX
> > into the back of the vanity, leaving a nice open bottom for "stuff". Pipes in the middle
> > of a vanity bottom are just a PITA. Make your life even easier and cut out some of the
> > drywall for better access. Hide it with the vanity.
> >
> > An example configuration...
> >
> > https://i.imgur.com/ym4ijXE.jpg
> >
> > If you hate plumbing, and you've never used SharkBites, ignore the cost and get it done in
> > a matter of minutes. Easy transition from copper to PEX. No solder, no glue, minimal layout.
> > Just push to fit. You don't even have to really line anything up, because once installed, they
> > rotate on the pipe, so just point them in the direction you need. They are easier than Fernco
> > couplings and just as permanent. ;-)
> >
> > https://www.sharkbite.com/us/en/brass-push-to-connect/fittings
> You're bad, really really bad. Now you are making me contemplate things. I will have to get over to the house and look at the basement again. See if I can figure out where the water supply lines are located. And if I can figure out where the stud bays for the walls are located. So I would even know where to drill holes up from the basement.
>
> As I maybe mentioned before, or not, the basement ceiling is covered in plywood. Only open spots are the few areas where some of the plumbing was run up to the bathrooms. Some of the drain lines. And some of the water lines.. A lot of the water and drain lines are buried in the walls and or within the covered up joist bays.
>
> For instance, the picture of the bathroom sink area with the drain line coming out of the wall. The one where you deleted out my water pipes coming up through the floor and added in red and blue Sharkbite lines coming out of the wall. That drain ties into a stack within the wall. So I do not know where that drain really is and do not know where the wall cavity is. That sink drain does not come out directly into the basement.
> So I do not know where to drill up through the floor and into the stud bay. And I don't think I know where the hot and cold water lines are either. Same with the other bathroom. Its drain out of the wall ties into the vertical stack within the walls in between the bathrooms. And I do not know where the water lines for the other bathroom originate from either. All the water supply lines just come up through the floor in both bathrooms.
>
> I think to find all of the hidden water and drain lines would mean tearing off a lot of the basement ceiling plywood. I guess there is a downside to having your basement ceiling covered in plywood.
>
> But your Sharkbite idea may be used by me for fixing the water line to the other bathroom's toilet. It has a flexible hose to the toilet that goes through the floor, and then ties into a threaded pipe connector, threads on both ends, which is connected to another flexible hose, and finally to a copper pipe with a soldered on threaded end. I am going to fix that mess. Had thought about soldering copper. But your Sharkbite will be a lot easier. I have access to that mess in the basement because its in joist bays where the plywood is cutout already.
>
> https://i.imgur.com/MqSNl53.jpg
> In a couple of the pictures I posted before it shows three vertical drains in the horizontal run. See link above. Farthest left sanitary T is the new black rubber Fernco I just installed. Second sanitary T has the black ABS plumbing pipe on top. Its the vent pipe through the roof. The black pipe coming out the left side gets the tub in the other bathroom. The black pipe coming out the right gets the two sinks. I think. The sink drain pipes are in the walls above. Or maybe hidden in the joists under the plywood. Third white elbow at the forefront is for the toilet in the other bathroom.
>
> Some water lines are visible in the basement. Water to the tub in the other bathroom for example. Toilet supply line for the half bath I worked on. I'm going to fix it as I described above. But not sure if I can find the sink water lines.
>
> I need to get over there again and look at things again.

On Tuesday, September 27, 2022 at 10:35:24 PM UTC-5, DerbyDad03 wrote:
> On Tuesday, September 27, 2022 at 11:16:33 PM UTC-4, russell...@yahoo.com wrote:
> > On Tuesday, September 27, 2022 at 4:51:37 PM UTC-5, DerbyDad03 wrote:
> > > On Tuesday, September 27, 2022 at 2:20:22 AM UTC-4, russell...@yahoo.com wrote:
> > > > On Monday, September 26, 2022 at 5:04:29 PM UTC-5, DerbyDad03 wrote:
> > > > > On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russell...@yahoo.com wrote:
> > > > > > On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > > > > > > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell....@yahoo.com wrote:
> > > > > > > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > > > > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell...@yahoo.com"
> > > > > > > > > > > <ritzann...@gmail.com> wrote:
> > > > > > > > > > >
> > > > > > > > > > > >For PVC gluing, these are the parts I need.
> > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > > > >
> > > > > > > > > > > >For the Fernco sanitary tee option.
> > > > > > > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > > > > > > usually.
> > > > > > > > > > >
> > > > > > > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > > > > > > nice. Quick and easy with existing plumbing is nice.
> > > > > > > > > > >
> > > > > > > > > > > Nice thoughts DerbyDad.
> > > > > > > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > > > > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > > > > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > > > > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > > > > > > per joint.
> > > > > > > > >
> > > > > > > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > > > > > > if you don't have any slack in the pipes.
> > > > > > > > >
> > > > > > > > > Don't take my word for it...
> > > > > > > > >
> > > > > > > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > > > > > > >
> > > > > > > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > > > > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > > > > > > and "it does not seem", it makes me think that you haven't done any research.
> > > > > > > > >
> > > > > > > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > > > > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > > > > > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > > > > > > > use them all the time.
> > > > > > > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > > > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > > > > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > > > > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > > > > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > > > > > > on both sides of the S-Tee
> > > > > > > > >
> > > > > > > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > > > > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > > > > > > > in that thinking.
> > > > > > > > >
> > > > > > > > > re: "Just glue the PVC flange to a short piece of 4" pipe.. Drop it down the hole."
> > > > > > > > >
> > > > > > > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > > > > > > >
> > > > > > > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > > > > > > >
> > > > > > > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > > > > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > > > > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > > > > > > plan on looking into it a little further for my own edification) They make one style for
> > > > > > > > > PVC pipes and one for cast iron.
> > > > > > > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > > > > > > >
> > > > > > > > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> > > > > > > >
> > > > > > > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> > > > > > > >
> > > > > > > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow.. Bigger hole with glued PVC flange is an advantage for a toilet.
> > > > > > > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > > > > > > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > > > > > > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > > > > > > fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
> > > > > > >
> > > > > > > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > > > > > > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > > > > > > PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> > > > > > > and it would be connected to the existing drain.
> > > > > > >
> > > > > > > Like this, but with a new S-Tee and vertical pipe.
> > > > > > >
> > > > > > > https://i.imgur.com/88G8ve9.jpg
> > > > > > OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
> > > > > >
> > > > > > BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
> > > > > >
> > > > > > Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
> > > > > >
> > > > > > https://i.imgur.com/MqSNl53.jpg
> > > > > > https://i.imgur.com/sXIC15n.jpg
> > > > > > https://i.imgur.com/LvB4dxX.jpg
> > > > > >
> > > > > > Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
> > > > > >
> > > > > > Here are links for the fixed subfloor and the new toilet flange..
> > > > > >
> > > > > > https://i.imgur.com/8FbjkBh.jpg
> > > > > > https://i.imgur.com/sl4Pxqo.jpg
> > > > > >
> > > > > > First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
> > > > > >
> > > > > > Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
> > > > > >
> > > > > > For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
> > > > > >
> > > > > > One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
> > > > > >
> > > > > > https://i.imgur.com/jHVgO4T.jpg
> > > > > >
> > > > > > DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.
> > > > > Good job! Looks great. Plumbing can be a pain, but for the most part
> > > > > it’s not all that hard - when you can get to what you need to get to.
> > > > >
> > > > > I’ve done similar jobs, but had to go in through a hole in the ceiling
> > > > > below. That’s the worst for me because I wasn’t born with the drywall
> > > > > mudding gene. It takes me forever and I’m rarely satisfied with the
> > > > > results.
> > > > >
> > > > > Good luck with the floor and fixtures. Paint first. ;-)
> > > > I love love love electrical work. Tolerate but do not like plumbing work. As for going through a hole, I recently added some lights into the garage. Accessed by an access panel and 8 foot step ladder. Crawled around on my hands and knees and belly on pieces of wood and plywood I brought up to span the trusses. Took several days and many hours. But I still liked that better than this plumbing work. I don't mind painting. Maybe because a freshly painted room always looks nice. Confirmation that you did something good.
> > > >
> > > > I'm reasonably happy with the finished job. Its right. But knowing what I know now, after doing it my way, I would do it your way the next time. As you described above of putting PVC sanitary T and stack and flange. Then use the rubber Fernco couplers to tie it into the horizontal run. Not that there will be a next time. Next time may be the other bathroom in the house. The one with the toilet still working. I probably cannot do a plumbing fix in there until we are ready to put in the vinyl flooring. Maybe do the plumbing fix the night before and the day the flooring installer is there.. Vinyl flooring install will be hired out.
> > > >
> > > > Yes, painting is next job to be done. Before flooring is installed. And install new ceiling fans. One worry I have is getting the new cabinets in. The water supply lines come up through the floor. So have to take the valves off, figure out where to drill holes in the floor of the cabinet, then drop it over the water pipes. All while maneuvering the cabinet over the drain pipes coming out of the wall. I think bathroom vanities come with an open back or a big opening in the back. So no cutting a hole by me. But I will look at bathroom vanities next time I am at the store.
> > > Just because the pipes come up through the floor now doesn't mean that they have to
> > > stay there.
> > >
> > > Get some SharkBite fittings and few short lengths of PEX. Cut the copper pipes down in
> > > the basement and route the PEX inside the wall where the sink drain is. Bring the PEX
> > > into the back of the vanity, leaving a nice open bottom for "stuff". Pipes in the middle
> > > of a vanity bottom are just a PITA. Make your life even easier and cut out some of the
> > > drywall for better access. Hide it with the vanity.
> > >
> > > An example configuration...
> > >
> > > https://i.imgur.com/ym4ijXE.jpg
> > >
> > > If you hate plumbing, and you've never used SharkBites, ignore the cost and get it done in
> > > a matter of minutes. Easy transition from copper to PEX. No solder, no glue, minimal layout.
> > > Just push to fit. You don't even have to really line anything up, because once installed, they
> > > rotate on the pipe, so just point them in the direction you need. They are easier than Fernco
> > > couplings and just as permanent. ;-)
> > >
> > > https://www.sharkbite.com/us/en/brass-push-to-connect/fittings
> > You're bad, really really bad. Now you are making me contemplate things.. I will have to get over to the house and look at the basement again. See if I can figure out where the water supply lines are located. And if I can figure out where the stud bays for the walls are located. So I would even know where to drill holes up from the basement.
> >
> > As I maybe mentioned before, or not, the basement ceiling is covered in plywood. Only open spots are the few areas where some of the plumbing was run up to the bathrooms. Some of the drain lines. And some of the water lines. A lot of the water and drain lines are buried in the walls and or within the covered up joist bays.
> >
> > For instance, the picture of the bathroom sink area with the drain line coming out of the wall. The one where you deleted out my water pipes coming up through the floor and added in red and blue Sharkbite lines coming out of the wall. That drain ties into a stack within the wall. So I do not know where that drain really is and do not know where the wall cavity is. That sink drain does not come out directly into the basement.
> > So I do not know where to drill up through the floor and into the stud bay. And I don't think I know where the hot and cold water lines are either.. Same with the other bathroom. Its drain out of the wall ties into the vertical stack within the walls in between the bathrooms. And I do not know where the water lines for the other bathroom originate from either. All the water supply lines just come up through the floor in both bathrooms.
> >
> > I think to find all of the hidden water and drain lines would mean tearing off a lot of the basement ceiling plywood. I guess there is a downside to having your basement ceiling covered in plywood.
> >
> > But your Sharkbite idea may be used by me for fixing the water line to the other bathroom's toilet. It has a flexible hose to the toilet that goes through the floor, and then ties into a threaded pipe connector, threads on both ends, which is connected to another flexible hose, and finally to a copper pipe with a soldered on threaded end. I am going to fix that mess. Had thought about soldering copper. But your Sharkbite will be a lot easier. I have access to that mess in the basement because its in joist bays where the plywood is cutout already.
> >
> > https://i.imgur.com/MqSNl53.jpg
> > In a couple of the pictures I posted before it shows three vertical drains in the horizontal run. See link above. Farthest left sanitary T is the new black rubber Fernco I just installed. Second sanitary T has the black ABS plumbing pipe on top. Its the vent pipe through the roof. The black pipe coming out the left side gets the tub in the other bathroom. The black pipe coming out the right gets the two sinks. I think. The sink drain pipes are in the walls above. Or maybe hidden in the joists under the plywood. Third white elbow at the forefront is for the toilet in the other bathroom.
> >
> > Some water lines are visible in the basement. Water to the tub in the other bathroom for example. Toilet supply line for the half bath I worked on.. I'm going to fix it as I described above. But not sure if I can find the sink water lines.
> >
> > I need to get over there again and look at things again.
> Ok, it just looked like the exposed pipe to left of the
> work you just did went right up to where sink pipes
> come up out of the floor. My error.
>
> Good luck with the rest of the job.

On Wednesday, September 28, 2022 at 4:23:10 PM UTC-4, russellseaton1@yahoo.com wrote:
> On Tuesday, September 27, 2022 at 10:35:24 PM UTC-5, DerbyDad03 wrote:
> > On Tuesday, September 27, 2022 at 11:16:33 PM UTC-4, russell...@yahoo.com wrote:
> > > On Tuesday, September 27, 2022 at 4:51:37 PM UTC-5, DerbyDad03 wrote:
> > > > On Tuesday, September 27, 2022 at 2:20:22 AM UTC-4, russell...@yahoo.com wrote:
> > > > > On Monday, September 26, 2022 at 5:04:29 PM UTC-5, DerbyDad03 wrote:
> > > > > > On Monday, September 26, 2022 at 2:34:44 AM UTC-4, russell...@yahoo.com wrote:
> > > > > > > On Tuesday, September 20, 2022 at 5:20:11 PM UTC-5, DerbyDad03 wrote:
> > > > > > > > On Tuesday, September 20, 2022 at 5:33:58 PM UTC-4, russell....@yahoo.com wrote:
> > > > > > > > > On Tuesday, September 20, 2022 at 2:15:36 PM UTC-5, DerbyDad03 wrote:
> > > > > > > > > > On Monday, September 19, 2022 at 11:57:02 PM UTC-4, russell...@yahoo.com wrote:
> > > > > > > > > > > On Monday, September 19, 2022 at 7:26:34 PM UTC-5, Markem618 wrote:
> > > > > > > > > > > > On Mon, 19 Sep 2022 17:10:28 -0700 (PDT), "russell....@yahoo.com"
> > > > > > > > > > > > <ritzann...@gmail.com> wrote:
> > > > > > > > > > > >
> > > > > > > > > > > > >For PVC gluing, these are the parts I need.
> > > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/nibco-reg-hub-pvc-sanitary-tee-dwv/k09920c/p-1444449194051-c-8571.htm?tid=-1130025097665889175&ipos=48
> > > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/4-pvc-sewer-and-drain-stop-coupling/36-665/p-1100429375664603-c-8571.htm
> > > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > > > > >
> > > > > > > > > > > > >For the Fernco sanitary tee option.
> > > > > > > > > > > > >https://www.amazon.com/Fernco-Inc-PQT-400-4-Inch-Degree/dp/B000BQQZEI
> > > > > > > > > > > > >https://www.menards.com/main/plumbing/pipe-fittings/pvc-pipe-fittings/pvc-sch-40-dwv-plain-end-cellular-core-pipe/pvc044001000hc/p-1444426398146-c-8571.htm
> > > > > > > > > > > > >https://www.menards.com/main/plumbing/plumbing-installation-repair/toilet-installation/sioux-chief-4-hub-pvc-toilet-flange/886-4ppk/p-1444442709166-c-9418.htm?tid=-5156148938299798422&ipos=53
> > > > > > > > > > > > If you do glue, set it up dry, mark across the joints with a marker so
> > > > > > > > > > > > you can line them back up. Marking would the flange on the floor so
> > > > > > > > > > > > the toilet is not skewed. You can turn them about an 1/8 to a 1/4 turn
> > > > > > > > > > > > usually.
> > > > > > > > > > > >
> > > > > > > > > > > > I think I would go with Fernco route though, easier to line it up
> > > > > > > > > > > > nice. Quick and easy with existing plumbing is nice..
> > > > > > > > > > > >
> > > > > > > > > > > > Nice thoughts DerbyDad.
> > > > > > > > > > > Thanks for the advice to do it dry and put marks on the pieces first. I knew it would be critical to make sure the sanitary tee was straight up and down and directly under the hole in the subfloor. But thought I'd just make it work. Doing it dry and putting marks on everything is much smarter.
> > > > > > > > > > The thing to be aware of with dry fitting PVC is that fittings do not
> > > > > > > > > > typically seat fully when dry. You'll get close, but they'll slip in farther
> > > > > > > > > > once the glue is applied. Sometimes it's as much as a 50% difference
> > > > > > > > > > per joint.
> > > > > > > > > >
> > > > > > > > > > Measuring the actual depth of the socket is actually the better option, especially
> > > > > > > > > > if you don't have any slack in the pipes.
> > > > > > > > > >
> > > > > > > > > > Don't take my word for it...
> > > > > > > > > >
> > > > > > > > > > <https://terrylove.com/forums/index.php?threads/is-there-a-trick-to-dry-fitting-pvc.62397/>
> > > > > > > > > > >
> > > > > > > > > > > For some reason, I don't like the Fernco option. It does not seem permanent.
> > > > > > > > > > Don't take this the wrong way, but when you use phrases like "for some reason"
> > > > > > > > > > and "it does not seem", it makes me think that you haven't done any research.
> > > > > > > > > >
> > > > > > > > > > A simple Google search for fernco vs. glue (or however you like to phrase your
> > > > > > > > > > search strings) may convince you that Fernco (or Fernco like fittings) are not
> > > > > > > > > > just for temporary connections. Look at some of the plumbing forums. Pros
> > > > > > > > > > use them all the time.
> > > > > > > > > > > Like glued in PVC pipe. BUT, I will look at a PVC sanitary tee at Menards and figure out if the Fernco sanitary tee comes built so it just slips into the place of a cutout tee. Based on its published length.
> > > > > > > > > > > Fernco extra long so it goes over the pipe ends, no making the pipe longer to use the Fernco. Because a glued in sanitary tee has to have the pipe about 4 inches longer because the ends of the sanitary tee go over the pipe by about 4 inches where its glued. I am definitely considering it. It would make everything real easy. Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole. Figure out how much needs to be cut off to make it the perfect length. Then screw the band clamps tight.
> > > > > > > > > > First, I'm not sure why you feel that the Fernco S-Tee has to fit without lengthening
> > > > > > > > > > the pipes once the caulked S-Tee is cut out. Assuming you get yourself to a point
> > > > > > > > > > where you trust Fernco couplings, just use a straight coupler to extend the pipes
> > > > > > > > > > on both sides of the S-Tee
> > > > > > > > > >
> > > > > > > > > > Maybe I'm missing something, but it sounds like you are almost willing to use a
> > > > > > > > > > a Fernco S-Tee *only* if fits right in, otherwise you'll use glue. I don't see the logic
> > > > > > > > > > in that thinking.
> > > > > > > > > >
> > > > > > > > > > re: "Just glue the PVC flange to a short piece of 4" pipe. Drop it down the hole."
> > > > > > > > > >
> > > > > > > > > > I didn't see any mention of the Oatey compression fit flange that I linked to:
> > > > > > > > > >
> > > > > > > > > > <https://www.amazon.com/Oatey-43539-Flange-Replacement-4-Inch/dp/B000DZHDQG>
> > > > > > > > > >
> > > > > > > > > > By using that flange along with Fernco fittings, you wouldn't have to glue *anything*.
> > > > > > > > > > If you don't already have glue available, you'd be buying glue and cleaner/primer for
> > > > > > > > > > one fitting. (admittedly, I have never used (or seen used) that Oatey flange, but I do
> > > > > > > > > > plan on looking into it a little further for my own edification) They make one style for
> > > > > > > > > > PVC pipes and one for cast iron.
> > > > > > > > > Again, thank you for the recommendation of the Fernco products. I think I am going to use the Fernco sanitary tee on this project. Menards sells it off the shelf. For cheaper than Amazon. So I can go to the store and look at it and measure it in person. Yeah. And I am coming around to believing it is a permanent solution. So Yeah!!!!!
> > > > > > > > >
> > > > > > > > > As for my wanting, wishing I could do it with glued PVC instead. Probably because houses are always built new and renovated with glued PVC. Not Fernco. Do plumbers ever build a new house using only Fernco products for the plumbing? Or do plumbers use Fernco for repairs and difficult to access places when repairing? I am guessing the latter. New houses are always built with glued PVC. (Or in the old days with cast iron or even copper.) So glued PVC is better?????? That is how my reasoning is working. And glued PVC is cheaper too. But that is not a concern here. I bet even the president and vice presidents of Fernco have houses with normal glued DWV pipes. They do not have only Fernco products for all their plumbing.
> > > > > > > > >
> > > > > > > > > I think the Fernco sanitary tee fits in without lengthening the pipe itself. Its a direct replacement. But I said that because if I have to glue to lengthen the pipe, then why not just glue a little more to put in a PVC glued sanitary tee. Sort of the if you have to do 80% of the work anyway, why not just do 100% of the work to get it perfect. That kind of logic. But I also realize the simplicity of putting the Fernco sanitary tee into place and then moving it to the perfect position and then screwing it tight. It has an advantage.
> > > > > > > > >
> > > > > > > > > I already own PVC glue and primer. So using it to glue the PVC flange and pipe for the vertical stack is simple and easy. Just slop primer and glue onto the ends, shove the pipe into the flange laying on the floor, and Boom, you are done. Easy. So the Oatey flange is a No for me. I can understand it would be useful if you were working where you did not have access to the vertical pipe and had to work from the top down. Such as a slab floor or crawl space. But I have access to all the plumbing from the top and basement. So there is zero reason not to glue the pipe and flange together. And the Oatey also makes the inside of the pipe smaller so less flow. Bigger hole with glued PVC flange is an advantage for a toilet.
> > > > > > > > Got it. That all makes sense. So, if I was in your situation, having the glue (which I do)
> > > > > > > > and not wanting to use the Oatey flange (for all the right reasons) I'd probably do what
> > > > > > > > I suggested earlier with my cut-cut Fernco-Fernco suggestion - unless the Fernco S-Tee
> > > > > > > > fits perfectly. I'll be surprised if it does...just sounds too easy. ;-)
> > > > > > > >
> > > > > > > > I'd glue the PVC flange on, drop the vertical pipe into the hole and screw the flange down in
> > > > > > > > the proper position. Then I'd glue short pieces of PVC pipe into the horizontal ports of a
> > > > > > > > PVC S-Tee and glue it to the bottom of the pipe from the toilet. Two Fernco couplings later
> > > > > > > > and it would be connected to the existing drain.
> > > > > > > >
> > > > > > > > Like this, but with a new S-Tee and vertical pipe.
> > > > > > > >
> > > > > > > > https://i.imgur.com/88G8ve9.jpg
> > > > > > > OH!!!!!!!!! Kind of sort of maybe possibly wish I had seen this post before I did what I did.
> > > > > > >
> > > > > > > BUT, I think it all turned out OK. I did the job!!!!!! Yeah for me!!!!!!!!!
> > > > > > >
> > > > > > > Here are some pictures of what I did. I used the Fernco sanitary T. 3" size since that is what my plumbing is. Its the black piece in the pictures of course. I had to put in a coupling since my math or cutting or something was not exactly right. Or I drilled the hole for the toilet stack in the not right spot. I did put it at 12" + a tiny bit from the wall. So its right. But I still had to put in a coupler and a short piece of pipe on the horizontal waste pipe.
> > > > > > >
> > > > > > > https://i.imgur.com/MqSNl53.jpg
> > > > > > > https://i.imgur.com/sXIC15n.jpg
> > > > > > > https://i.imgur.com/LvB4dxX.jpg
> > > > > > >
> > > > > > > Three links above are the Fernco sanitary T I installed on the horizontal run. First link is the total run. Second and third links are just the installed T and the new coupler I had to put in. On the horizontal waste run, the furthest right elbow is for the other toilet. Middle black stack is for the sinks in both bathrooms and the washing machine. And the furthest left stack is the new sanitary T one I put in.
> > > > > > >
> > > > > > > Here are links for the fixed subfloor and the new toilet flange.
> > > > > > >
> > > > > > > https://i.imgur.com/8FbjkBh.jpg
> > > > > > > https://i.imgur.com/sl4Pxqo.jpg
> > > > > > >
> > > > > > > First link is just the patched subfloor. On the right of the patch, a little bit of the subfloor is still not perfect. But that tiny bit rotted wood is in the other joist bay. So I could not get to it for replacement. Its not bad so I am not worried about it. Vinyl flooring on top will be fine covering it. Second link is the toilet and sink area. I will have to cut the sink pipes lower and cut holes in the bottom of the vanity. And maybe cut a big hole in the back of the vanity to get it over the drain pipe elbow. That is after the vinyl floor is installed.
> > > > > > >
> > > > > > > Now, considering your suggestion of putting the toilet stack in place and gluing a PVC sanitary T to it. And gluing in a couple short pieces to it for the horizontal run. Then using Fernco couplers to tie it all in. Maybe, possibly, probably, I would have done that if I could redo everything. Using the Fernco sanitary T as I did worked. But your idea might have been even better.
> > > > > > >
> > > > > > > For the subfloor patch it turned out to be 5/8" plywood. I had a scrap piece I used as a cutting board for shingles last November when I roofed a house. Used the Festool track saw to get it to the right size. Milwaukee reciprocating saw to cut the plumbing pipes out. Makita sliding saw in chop mode to cut the new 3" pipe. Electric 1/2" drill and a hole saw I already owned for the toilet flange. Bosch jigsaw got used somewhere too. Makita cordless drill was used for all the screw drilling and driving of course. Manual handsaw and screwdrivers of course. Socket wrench to tighten the Fernco band clamps. All in all, it was a bigger job than one would imagine.
> > > > > > >
> > > > > > > One more picture link. This is of the other toilet stack for the other full bathroom. The one I worked on is a half bath. The hole cut for the toilet flange is bad, not round. And it is showing a little rot. So when I take out that toilet for a new vinyl floor, I will also replace some subfloor. And likely glue in a new long turn 90 degree elbow on the bottom for the horizontal run in the basement. And drill a hole in the new subfloor and glue in a piece of pipe to the toilet flange. And glue the stack to the elbow. All glued PVC.
> > > > > > >
> > > > > > > https://i.imgur.com/jHVgO4T.jpg
> > > > > > >
> > > > > > > DerbyDad03, notice that this stack has a Fernco coupler. It was put in before 2010 when we acquired the house. Prior owner maybe put a new toilet stack in and the plumber figured the easiest way to get a new stack was to use the Fernco coupler.
> > > > > > Good job! Looks great. Plumbing can be a pain, but for the most part
> > > > > > it’s not all that hard - when you can get to what you need to get to.
> > > > > >
> > > > > > I’ve done similar jobs, but had to go in through a hole in the ceiling
> > > > > > below. That’s the worst for me because I wasn’t born with the drywall
> > > > > > mudding gene. It takes me forever and I’m rarely satisfied with the
> > > > > > results.
> > > > > >
> > > > > > Good luck with the floor and fixtures. Paint first. ;-)
> > > > > I love love love electrical work. Tolerate but do not like plumbing work. As for going through a hole, I recently added some lights into the garage. Accessed by an access panel and 8 foot step ladder. Crawled around on my hands and knees and belly on pieces of wood and plywood I brought up to span the trusses. Took several days and many hours. But I still liked that better than this plumbing work. I don't mind painting. Maybe because a freshly painted room always looks nice. Confirmation that you did something good.
> > > > >
> > > > > I'm reasonably happy with the finished job. Its right. But knowing what I know now, after doing it my way, I would do it your way the next time. As you described above of putting PVC sanitary T and stack and flange. Then use the rubber Fernco couplers to tie it into the horizontal run. Not that there will be a next time. Next time may be the other bathroom in the house. The one with the toilet still working. I probably cannot do a plumbing fix in there until we are ready to put in the vinyl flooring. Maybe do the plumbing fix the night before and the day the flooring installer is there. Vinyl flooring install will be hired out.
> > > > >
> > > > > Yes, painting is next job to be done. Before flooring is installed. And install new ceiling fans. One worry I have is getting the new cabinets in. The water supply lines come up through the floor. So have to take the valves off, figure out where to drill holes in the floor of the cabinet, then drop it over the water pipes. All while maneuvering the cabinet over the drain pipes coming out of the wall. I think bathroom vanities come with an open back or a big opening in the back. So no cutting a hole by me. But I will look at bathroom vanities next time I am at the store.
> > > > Just because the pipes come up through the floor now doesn't mean that they have to
> > > > stay there.
> > > >
> > > > Get some SharkBite fittings and few short lengths of PEX. Cut the copper pipes down in
> > > > the basement and route the PEX inside the wall where the sink drain is. Bring the PEX
> > > > into the back of the vanity, leaving a nice open bottom for "stuff".. Pipes in the middle
> > > > of a vanity bottom are just a PITA. Make your life even easier and cut out some of the
> > > > drywall for better access. Hide it with the vanity.
> > > >
> > > > An example configuration...
> > > >
> > > > https://i.imgur.com/ym4ijXE.jpg
> > > >
> > > > If you hate plumbing, and you've never used SharkBites, ignore the cost and get it done in
> > > > a matter of minutes. Easy transition from copper to PEX. No solder, no glue, minimal layout.
> > > > Just push to fit. You don't even have to really line anything up, because once installed, they
> > > > rotate on the pipe, so just point them in the direction you need. They are easier than Fernco
> > > > couplings and just as permanent. ;-)
> > > >
> > > > https://www.sharkbite.com/us/en/brass-push-to-connect/fittings
> > > You're bad, really really bad. Now you are making me contemplate things. I will have to get over to the house and look at the basement again. See if I can figure out where the water supply lines are located. And if I can figure out where the stud bays for the walls are located. So I would even know where to drill holes up from the basement.
> > >
> > > As I maybe mentioned before, or not, the basement ceiling is covered in plywood. Only open spots are the few areas where some of the plumbing was run up to the bathrooms. Some of the drain lines. And some of the water lines. A lot of the water and drain lines are buried in the walls and or within the covered up joist bays.
> > >
> > > For instance, the picture of the bathroom sink area with the drain line coming out of the wall. The one where you deleted out my water pipes coming up through the floor and added in red and blue Sharkbite lines coming out of the wall. That drain ties into a stack within the wall. So I do not know where that drain really is and do not know where the wall cavity is. That sink drain does not come out directly into the basement.
> > > So I do not know where to drill up through the floor and into the stud bay. And I don't think I know where the hot and cold water lines are either. Same with the other bathroom. Its drain out of the wall ties into the vertical stack within the walls in between the bathrooms. And I do not know where the water lines for the other bathroom originate from either. All the water supply lines just come up through the floor in both bathrooms.
> > >
> > > I think to find all of the hidden water and drain lines would mean tearing off a lot of the basement ceiling plywood. I guess there is a downside to having your basement ceiling covered in plywood.
> > >
> > > But your Sharkbite idea may be used by me for fixing the water line to the other bathroom's toilet. It has a flexible hose to the toilet that goes through the floor, and then ties into a threaded pipe connector, threads on both ends, which is connected to another flexible hose, and finally to a copper pipe with a soldered on threaded end. I am going to fix that mess. Had thought about soldering copper. But your Sharkbite will be a lot easier. I have access to that mess in the basement because its in joist bays where the plywood is cutout already.
> > >
> > > https://i.imgur.com/MqSNl53.jpg
> > > In a couple of the pictures I posted before it shows three vertical drains in the horizontal run. See link above. Farthest left sanitary T is the new black rubber Fernco I just installed. Second sanitary T has the black ABS plumbing pipe on top. Its the vent pipe through the roof. The black pipe coming out the left side gets the tub in the other bathroom. The black pipe coming out the right gets the two sinks. I think. The sink drain pipes are in the walls above. Or maybe hidden in the joists under the plywood. Third white elbow at the forefront is for the toilet in the other bathroom.
> > >
> > > Some water lines are visible in the basement. Water to the tub in the other bathroom for example. Toilet supply line for the half bath I worked on. I'm going to fix it as I described above. But not sure if I can find the sink water lines.
> > >
> > > I need to get over there again and look at things again.
> > Ok, it just looked like the exposed pipe to left of the
> > work you just did went right up to where sink pipes
> > come up out of the floor. My error.
> >
> > Good luck with the rest of the job.
> I think those pipes are for the washing machine. The two bathrooms and washing machine are arranged all touching each other. To share drain pipes and water of course. The washing machine and half bath (I worked on) are along the outside of the house. Washing machine is east. Half bath is west. The full bath is inside of both of those rooms to the north. Its a big square. But inside of the other two rooms. It does not touch the outside wall.
>
> I will get back over to the house sometime soon and reassess everything. Figure out if it is possible to put the water pipes in the wall or not. But right now I think I only know where the hot and cold water pipes for the shower and washing machine are located. Bathroom pipes are hidden up in the joists, covered by plywood. But I can get to both toilet water pipes. They are in already cutout exposed areas. And I will use the Sharkbite connectors to fix one of the toilet water pipes. My Ridgid compact pipe cutter, a straight coupler, 12" of copper pipe, an elbow coupler, 12" of copper pipe, and a shutoff valve on top.
>
> Funny thing. I did use Sharkbite connectors about 15 years ago. I installed a toilet and sink in my basement of the prior house. All pipes were easily seen and exposed in the joists. I put a Sharkbite T into the hot and cold master shower pipes and ran the water over to the wall. I used CPVC for my new water lines. Old pipe in house was copper. The Sharkbites I used were the yellow/white CPVC color, and plastic of course. They were not the brass pretty solid ones shown in the link you posted. The Sharkbites then saved me from having to solder copper pipes. I was happy about that. Gluing CPVC is so much easier. The Sharkbites I installed 15 years ago never ever gave me any problems. So I know they do work. But I had just forgotten they were an option to fix my current plumbing problems.
>
> https://www.menards.com/main/plumbing/pipe-fittings/push-to-connect-fittings/watts-reg-aqualock-trade-push-to-connect-lead-free-brass-coupling/0472000/p-1444446192233-c-12709.htm?tid=-1209553812764759867&ipos=1
>
> https://www.menards.com/main/plumbing/pipe-fittings/push-to-connect-fittings/watts-reg-aqualock-trade-push-to-connect-lead-free-brass-elbow/0472016/p-1444446179359-c-12709.htm?tid=-1209553812764759867&ipos=5
>
> Above are what I will use to fix my toilet water supply line. And 1/2" copper pipe I already own. And a shutoff valve I already bought.